Tuff Country Ladder Bars

A: Ford F250/F350 4wd | 1999-2004 | Rear Axle | PN: 20990

A: This PN: T/C10892 - fits the Chevy Silverado 2500HD | Crew Cab | Short Bed | 2011-2016 | Check out the Rough Country Traction Bar Kit - PN: R/C11001 | 2011-2019 | 4WD | Chevy | Silverado 3500 & 2500HD.

A: 1988-1998 Chevy truck 1500, 2500, 3500 4WD | Rear - PN: T/C10890 Ladder bars help reduce axle hop or wrap, thus providing increased traction and acceleration by maintaining tire contact with the road.

A: Ladder bars normally need at least 1” of spacing between the axle and leaf spring to install air bags

A: Yes they will work.

A: Yes this should work for you.

A: Per Tuff Country: If the vehicle is lifted with blocks then it should work. if it is lifted with Leaf springs only, then they will not clear the new leaf spring

A: 43" long

A: Overall Length (in):43.000 in.

A: Thanks for the inquiry Jack, the Tuff Country Tuff Country Ladder Bar part # t/c30995 will fit 1994-2002 ram 2500.

A: Gears- Thank you for your question. The Tuff Country Tuff Country Ladder Bar will fit your 04 excursion but may require some modification of the truck or upper frame mount.

A: Dex- Thank you for your question. The Tuff Country Tuff Country Ladder Bar will work with the factory Fits 1980 to 1996 Ford F150/F250/F350 4WD rear end.

A: Hello Anthony, Thank you for the question. Yes, the Tuff Country Tuff Country Ladder Bar T/C20990 can be installed with a 6" lift kit with a few minor modifications .

A: Hi Bob This kit will fit your truck with the 4" lift with out a problem. I don't have one here where i am at to measure and the vendor does not have the information on hand but it is approximately 6" wide . Thank You

A: Hello ridehigh, Thank you for the question. No, the Tuff Country Tuff Country Ladder Bar T/C10890 fits the 1988 to 1998 GM (Chevy/GMC) 1500, 2500 or 3500. The correct part number is T/C20990. The T/C20990 will fit the 1999 to 2004 Ford F250/F350 4WD.

A: Hello Jab, Thank you for the question. The Tuff Country Tuff Country Ladder Bar T/C10890 fits the 1988 to 1998 GM 1500/2500/3500. Please provide all of your vehicle details including year so I can get you the correct part number.

A: Hi Josh I kneed to know more vehicle information to verify fitment. Year, Make, Mode,l Cab Style, Bed length. Thank You

A: Hi Dave The Tuff Country bars mount to the rear axle by sandwiching a plate between the axle and lift block or leaf spring. This plate will have the lower mount for the bars to hook to.Thank You

A: Hi Mike The 1966 Ford F-250 should have come with a Dana 60 rear axle with axle tubes between 3-3 1/2" in diameter. The EXP72500B axle bracket kit should fit your rear axle then you will have a choice of bar length of 42",50", 63", 67",and 74". You are going to want to land the front bar right in the range of were the transfer case and drive shaft meet with in reason + or - a few inches.. if your intention it to actually mount these on your Dana 44 Front axle we have no bracket kits that will fit a front axle. you will have to fabricate your own axle mounts Thank you

A: Hi Mike I am sure we have a kit that will accommodate your Dana 44 axle but i will need to know your vehicle information so i can give you the appropriate part numbers and verify fitment to your specific vehicle and lift height. thank you

A: Hello Mike, No, the Tuff Country Ladder Bar T/C20890 is designed for a 3.75" diameter rear axle tube (Dana 60/GM 14 Bolt). Thank you for the email.

A: Hello James, Yes, the Tuff Country Tuff Country Ladder Bar T/C20990 will fit your vehicle application. It does included the mounting brackets. Thank you for the email.

A: The Tuff Country Ladder bars come with their own bracket to bolt to.