A: I drilled holes on the fender support that runs at about a 45 degree angle and mounted it on the bumper side, cant see it and its well protected

A: No. I relocated mine under the hood on drivers side. Need 4’ of vacuum hose and a couple self tapping screws.

A: I have the Vaccum bottle. It does not come with mounts but yes it has plenty of space I drilled and did some self tapping screws and extended the Vaccum line and it tucked in nicely. 

A: It does have space for the vacuum bottle, but no mounts. I mocked it up and drilled the holes and used the original hardware to mount it.

A: Yes. I got my adapters from Etrailer. They have a sleeve that you knock into the holes where the shackle go. Only problem is that you won’t be able to use 3/4” shackles for vehicle recovery. But you can use 5/8” shackles. I run a soft shackle or a tree strap thru both shackles if I get stuck.    Don’t skimp on a tow bar, if you do, you will regret it. Etrailer has everything you need. Good luck!

A: Yes. I got mine from Etrailer. They are excellent! Only problem is that the tow bar attachments have a sleeve that you tap into the shackle mount. That means you can’t use a 3/4” shackle. You can use a 5/8” shackle, but it’s a tight fit. When getting winched I use a soft shackle or tree strap run thru both shackles. Don’t skimp on a tow bar, you will regret it. Etrailer will get you right, and good luck!

A: Depends on what mounts really. The d-rings are rated to be used as towing points.

A: I can’t tell you positively that they would, but most winches should fit as the bolt pattern is similar to most brands.My Smittybuilt winch is a 10K winch. 

A: Hello 907Driven, The Smittybilt XRC Rock Crawler Winch Bumper with D-ring Mounts does not have a bull bar. You can purchase the XRC Front Bull Bar Option part #S/B76811 that bolts right on. Thanks for your question.

A: Steve, The XRC Front Bumper with Winch Plate S/B76810 has the bull bar holes integrated into the bumper.

A: Hey JAW, the Smittybilt XRC Rock Crawler Winch Bumper with D-ring Mounts has a weight of 117lbs. Thanks for your question.

A: Dutch, the Smittybilt XRC Rock Crawler Winch Bumper with D-ring Mounts doesn't affect the horn or vacuum tank. Hope this helps!

A: Thanks for the inquiry Xjuan, the Smittybilt XRC Rock Crawler Winch Bumper with D-ring Mounts part # S/B76810 McAllen does not have but we can order from Dallas.

A: No the store was correct the Smittybilt XRC Rock Crawler Winch Bumper with D-ring Mounts will have to be ordered in. Hope this helps!

A: Hello Xjuan, the Smittybilt XRC Rock Crawler Winch Bumper with D-ring Mounts part# S/B76810 is good in stock. Thank you for your question.

A: Hey Nicolas, this will take 3/4 d-ring and this would fit a 6 inch light bar. Thanks for your question.

A: Hello RyanXJ from NJ and thank you for the inquiry on the Smittybilt XRC Rock Crawler Winch Bumper with D-ring Mounts. This bumper accepts a 3/4" d ring: http://jo.my/bfip3f.qrcode

A: Brett- Thanks for the question. The Smittybilt XRC Rock Crawler Winch Bumper with D-ring Mounts weighs in at 117 lbs. This amount of weight could cause the front end to lower a bit. You could use a Rubicon Express Coil Spring Spacer to lift it back to the original height which you can find here http://jo.my/4rbpdd

A: Nate this bumper has a winch plate built in. It's stout enough to accommodate a 15,000 lb winch if you choose. Yes the D-rings are included.