The all new JK XRC M.O.D. (Multi Optional Design) Bumper System allows you to design your bumper for any terrain. The base unit was developed around our XRC platform and comes standard with a winch cradle with capacity to support up to a 15,000lb. winch. Its also equipped with D-Ring mounts that are welded on the inside and out that provides a towable anchor when pulling your rig behind a truck or motor home. Choose between our Mid or Full Width End Plate knowing that bumper clearance wont be sacrificed when wheeling in the harshest conditions. Then decide which over rider you prefer, you can choose between our low profile bull bar or our high point stinger.
Nice looking and easy to install well made has a lot of nice add on options
It was a super easy install, only one of the four front bolt holes on the vehicle bumper frame required minor drilling to fit bumper bolts. Great looking product!
This bumper is great. heavy duty with a real nice look.
I just installed this on a 2012 Wrangler and it looks way better than the stock bumper. However when installing the directions were not clear on where to use washers and how much you need to drill out the holes like it says in the directions. Also the holes for the add on parts where the stainless parts go the powder coat made it rough going to screw in those bolts. I would recommend this to other to install! Looks great and gives the Jeep a better looking front end.
This bumper is a beast, I love every inch of it. Installed on a 2015 JKURHR to replace the flimsy factory/aftermarket bumper. Installation Notes: 1) Follow the instructions with regards to installing and wiring the winch first. If not you will be removing it to do so... 2) Be prepared to "persuade" bolts to line up on your particular vehicle. Remember, they are made to fit several models. 3) Loctite all bolts, or you will replace them later. 4) Lastly this is a two man job, especially if you have a winch on it. Much too heavy to safely install solo.
The bumper looks great and my Warn VR8000 fit right in with room to spare. Seems to be well built. Wobble sockets and extensions made life a lot easier. The instructions are pretty vague, especially for a novice.
I have yet to try out the product to it's fullest but so far so good. Horrible on the installation though. Bolt holes for the main section had to be drilled out more then what was stated. I also bought the full width extensions as I love the fogs. Was told that I would be able to connect with the stock wiring...... Not even close. Cut the wires and hard wire it. Then your good. I also bought the stinger. Not to bad to install. A little tight as I installed the XC8 Winch first. (Highly recommend). As far as off road durability. I question the stinger as its a bolt on and not welded. We shall see.
Q: Im sure many are as confused as i am as youve said this product needs vacuum pump relocation kit and youve said it doesnt so i would just like to know if my 2014jku needs the relocation kit or not Answer this question
A: Hello MudSlinger, All 2012 and newer Jeep JK Wranglers will require a vacuum pump relocation bracket. Thank you.
Answered by RK on 07/01/2015
Q: Will this fit my 2015 JKU it says it will in the description but I chose my vehicle and it is saying that it won't fit Answer this question
A: Thanks for the inquiry Chuckie, the Smittybilt XRC M.O.D. Modular Center Section with Winch Plate and D-ring Mounts part # S/B76825 this will fit your 2015 JKU.
Answered by RK on 05/31/2015
Q: Does the winch have to be installed prior to instalation or can I add after it is mounted? Answer this question
A: Hello Geof, TheSmittybilt XRC M.O.D. Modular Center Section with Winch Plate and D-ring Mounts can be installed after.
Answered by Dave on 03/01/2015
Q: is there a matching rear bumper to this? Answer this question
A: We have many rear bumpers that match the front by smittybilt.
Answered by Morgan on 02/02/2015
Q: Will the winch plate of the MOD bumper accommodate an M12000 Warn winch in the front/foward mount configuration as required by Warn? Thanks, Joe Answer this question
A: Hello Gijoe, the Smittybilt XRC M.O.D. Modular Center Section with Winch Plate and D-ring Mounts part# S/B76825 will accommodate the Warn m12000 winch. Thank you for your inquiry.
Answered by mikey on 08/13/2014
For 60 years Smittybilt has been fabricating aftermarket parts and today their products include Jeep tops, bumpers, lighting, winches and trail gear. Off-roaders count on the company's innovative parts like the original nerf bar side steps to equip their Jeeps for the trail and day-to-day driving. Pairing affordability without compromising quality is the hallmark of Smittybilt and the manufacturer's reputation carries over to products like its Overlander Series of tents, Adventure Boxes and SEMA award-winning magnetic trail skins for Jeeps. Smittybilt offers over 2,000 interior and exterior parts and accessories for 4x4s with multiple capabilities for jeepers of all levels. Shop Smittybilt Now
Join our mailing list to receive information on new products, special events, discounts and more!
Sign up to receive deals by email!
Sign up to receive text alerts about new product releases, exclusive access to sales, and much more!
Sign up to receive deals by text!