Smittybilt XRC GEN2 Recovery Winches

A: I would not use nor do I use an in-line fuse. During heavy pulling it can exceed the current capability of your battery or alternator internal regulator, unless the fuse is <150amps and slo-blow, it will blow everytime if you put a dead load on it... if neither object is moving you could in theory pull 550 starting amps, ouch. That’s why you need a 650cca battery and minimum 160Amp alternator. In fact I only run 750-800cca amp battery, deep cycle, sealed gel and a 200amp alternator on all 3 of my jeeps... No start situations are a no no! If you shut down right after a hard pull, past 2 windings, on a factory 600cca battery and 160Amp  system, (alternator stock) cold outside or 2-3 year old battery, pray to Jeep gods the 400amp starter will do its job or you get to push if manual or call a buddy if automatic... a good 160Amp alternator at 1200 rpm on a brand new stock battery will take 20-30 minutes to reach a fully charged state after a 2-3 minute hard pull on the winch and if your running (My) 42” LED bar, 6 4” cubes, headlights and fog lights which go through the clock spring and TIPM... which mine do because of state lighting laws, your battery or winch solenoid could actually be drained to point of no return or burn through on output winding side. The TIPM and clock spring  system power distribution and priority will deprive power to direct connect aftermarket items to support and protect ECM/TCM/CANBUS. “ASSUMING 2007JK and later.”

A: I don't have one, nor do any of my friends have one on their winch. This winch, per the manual, draws 435 A at maximum pulling capacity. I don't remember ever seeing a fuse that big. HTH.

A: It comes factory with a 3 amp mini blade fuse. Early winches use a 5mmx20mm glass fuse 3 amp. Both are time delay.

A: You will need a mounting plate. Unless you have an aftermarket bumper with a place to secure the winch with the supplied nuts and bolts.

A: You will need some kind of adapter that the winch bolts to that will attach to your truck.

A: This winch has a 10”x4.5” bolt pattern and has a non-integrated solenoid.

A: As long as you have the winch mount or a bumper with a winch mount, this comes with everything you need to install.

A: Here's a link that will show line speed at different loads for this winch: https://www.smittybilt.com/downloads/SB_Gen2Winch_NPA-Extended.pdf

A: It depends on which ARB bumper you are referring to. Please confirm your bumper with our sales team to verify fitment Toll Free: 1-877-474-4821

A: Most of these bumpers are designed to fit 12k winches. Please call our sales line to see if there is any other bumpers available for this size winch Toll Free: 1-877-474-4821

A: Thanks for the inquiry Dave, the Smittybilt XRC-9.5K Waterproof Winch Gen2 part # S/B97495 you'll need part # WAR21390.

A: Hello Tim The S/B97495 does not come with a mounting bracket. Typically the winch would mount to a vehicle specific winch bumper. Smittybilt does also offer a universal winch mount cradle that the winch will mount to and then the cradle will mount into a 2 inch receiver hitch. The winch cradle is part # S/B2811. The 8ft winch quick connector kit is part # S/B35220 and the 24ft kit is S/B35210. Thank You for your question. Jon Snyder 4Wheelparts

A: Hello Big E, You will need the Smittybilt Winch Plate Part Number: S/B2804. Thank you for the question.

A: Hello Brandon and thank you for your question! Smittybilt XRC-9.5K Waterproof Winch Gen2 will fit in the Bestop Highrock 4x4 narrow front bumper.

A: Hello Jesus and thank you for your question! Smittybilt XRC-9.5K Waterproof Winch Gen2 will work in any winch mount with a bolt pattern of 10'x4.5".

A: Thanks for the inquiry Lisa, the Smittybilt XRC-9.5K Waterproof Winch Gen2 part # S/B97495 the replacement is part # S/B97495-50.

A: Hello Chase, Yes, this will fit your vehicle application. Thank you for the question.

A: Hello jeffmelendrez, We offer the Fab Fours Winch Mount Part Number: FFIFS99-N1650-1 for your vehicle application. This will accept the Smittybilt XRC-15.5K WINCH GEN2 S/B97415. Thank you for the question.

A: Thanks for the inquiry Michael, the Smittybilt XRC-9.5K Waterproof Winch Gen2 part #S/B97495 this will work in an ARB bumper.

A: Hello Bob, No, the correct part number for wireless is S/B97510. Thnak you.

A: Hello Mark, Yes, this winch will fit the Buckstop Classic II bumper. Thank you.

A: Thanks for the inquiry ninja jeep, the Smittybilt XRC-9.5K Waterproof Winch Gen2 part # S/B97495 this winch will fit no problem, all the hardware will come with the winch.

A: Hello Jlanc, You you also need the Smittybilt Winch Plate S/B2802 to complete the installation on your vehicle. Thank you.

A: Hello Mike, The Smittybilt XRC-9.5K Waterproof Winch Gen2 Part Number: S/B97495 come with the positive and negative battery leads. Thank you.

A: Hi Elias The S/B97495 will fit on your 2013 F150 with a Warn Transformer 2 mounting system. It is designed to fit a 4wd F150. It will not fit an Ecoboost model. The system comes in black and in polished stainless. You can see it on the Warn web sight. The black powder coated system is priced well. there are some options. Here is some of the part numbers for the black system. WAR90125 bracket kit $359.99 WAR88240 winch carrier $197.99 This is what is required to do the job. The options are a tall grill guard,a outer headlight guard,a light bar. These all work with the tall grill guard. The other option is a short grill guard. Let me know if you have any questions Thank You Jon Snyder 4Wheelparts

A: Sir, you will need a raised plate part# S/B2802 in order to mount the winch hope this helps thanks for the question.

A: Bill, this winch comes with everything to install except the mount you would have to have an aftermarket bumper with winch availability, which you have plenty of options just browse thru our website just add your vehicle info and all the bumpers will list for you. hope this helps thank you for your question.

A: Hello Bridgestoneivan, The Smittybilt XRC-9.5K Waterproof Winch Gen2 S/B97495 will fit perfect with the XRC Gen 2 Front Bumper. Thank you.

A: Hello Phrank, the Smittybilt XRC-12K WINCH GEN2 part# S/B97412 comes with everything you will need to install it on your new bumper. Thank you for your question.

A: Reaper from kailua hawaii,Thanks for the question.If you order the bumper & winch you will be ready to go.

A: Hello there, the Smittybilt XRC-9.5K Waterproof Winch Gen2 are made over seas. Shop with us anytime, on your schedule. Browse 4WheelParts.com, call our customer service center, or come visit us in one of our stores. You can even save on shipping costs by shopping online and picking your order up in a store. No matter which method you prefer, we’re ready to help with excellent parts, advice, and service.

A: Hello TX, Thank you for asking. Here is a link to a cover that will fit your daughters Smittybilt XRC-9.5K Waterproof Winch Gen2 http://jo.my/gg5fme

A: Hello Wayne, The Smittybilt XRC-9.5K Waterproof Winch Gen2 comes with the mounting hardware. If your winch did not come with it please call Smittybilt at (888)717-5797

A: All Smittybilt XRC-12K WINCH GEN2 are universal and require a mounting, aftermarket bumper or 2" receiver to install. The 400 price is the current sale price and can change without notice. Hope this helps!

A: Hello Colton, The Smittybilt XRC-9.5K Waterproof Winch Gen2 will require you to purchase the a winch plate for a aftermarket bumper.

A: The Smittybilt XRC-12K WINCH GEN2 is a direct bolt on to the S/B76800. You shouldn't need anything else. Hope this helps!

A: Hello Jerry and thank you for the inquiry on the Smittybilt XRC-9.5K Waterproof Winch Gen2. This winch has a limited lifetime warranty for mechanical and a 5 year electrical warranty. Here is the link to get you back to the ordering page: http://jo.my/mgvl7f.qrcode

A: Hello PT and thank you for your question! Smittybilt XRC-12K WINCH GEN2 will fit in the Smittybilt XRC Mod Bumper for your JK.

A: Thanks for the inquiry Ron, the Smittybilt XRC-9.5K Waterproof Winch Gen2 part # S/B97495 you can send a photo to [email protected] and they'll forward it to sales.

A: Hello Coloradowheeler from Colorado, and thank you for the inquiry on the Smittybilt XRC-9.5K Waterproof Winch Gen2. A Smittybilt XRC winch is a complete recovery system with the muscle and reliability to bail you out of any situation. click here to get back to the order page: http://jo.my/av67ci.qrcode

A: Yes you can use the Smittybilt XRC-9.5K Waterproof Winch Gen2 for pulling deer. You just need to connect it to a power source and you're good!

A: Chris, The Smittybilt XRC-9.5K Waterproof Winch Gen2 will work on any bumper that has a winch mounting plate all ready installed.

A: Hello Ryan, the Smittybilt XRC-9.5K Waterproof Winch Gen2 part# S/B97495 has a limited lifetime warranty. 3 years electronics and lifetime on the housing. Thank you for your inquiry.

A: Hello Bunee, This Smittybilt XRC-9.5K Waterproof Winch Gen2 will fit in any winch bumpoer with a 10x4.5 bolt pattern. Just measure the 4 hole predrilled for the winch in the bumper. They should be 10 inches apart and 4.5" wide. If that is the bolt pattern the winch is a direct fit.

A: Thank you for the question Rick. The Smittybilt XRC-9.5K Waterproof Winch Gen2 will free spool out. However it will not winch out in order to lower something. Thank you

A: Hello there, we get a lot question on winches but hardly on the roller fair-lead. here the answer to your question Length:10.0" (254mm).

A: Hello Adam, The Smittybilt XRC-9.5K Waterproof Winch Gen2 cable weight is about 17lbs.

A: Thanks for the inquiry Zuk Guy, the Smittybilt XRC-9.5K Waterproof Winch Gen2 part # this is a special this month will qualify for a free winch cover in any sales channel.

A: Hello Robert This winch will work on your vehicle, but you will have to choose an option for mounting it on your truck. The first is option is Warn Transformer grille guard (Part # WAR29753) and winch carrier (Part # WAR29165) The second would be a front mount receiver (Part # DRA65005) and winch cradle (Part # S/B2811). You will also need and quick connect/ disconnect (Part # 22680) This winch does not have a wireless remote. if you would like the wireless remote version you want to order (Part # S/B97512) Thank you Brian Dozois 800-337-9005 x 5125 [email protected]

A: brad, Thank you for your question. Smittybilt XRC-9.5K Waterproof Winch Gen2 Part Number: S/B97495 does have a removable solenoid box so that it can be mounted somewhere close by the winch.

A: Hello Tom, Thank you for the question. Every XRC winch includes a heavy duty winch controller, four-way roller fairlead, forged steel tow hook

A: Hello Bubba, Thank you for the question. Yes. We recommend 10K to 12K for that truck weight.

A: Zachary- Thanks for the question. The Smittybilt XRC-9.5K Waterproof Winch Gen2 does not come with a mounting plate. The base bolt pattern is a standard 10 x 4.5 inches.

A: Hi rlpetty43 The Smittybilt XRC winches do come with a hook for the end of the cable. All the XRC and X20 winches from 8000 to 17,000 all share the the same mounting pattern of 10" X 4.5". Thank You

A: jadams00- Thanks for your question. The Smittybilt XRC-9.5K Waterproof Winch Gen2 with steel cable does not come with hook.

A: Hi First timer Yes the winch will fit the winch plate and bumper with no modifications. Thank You

A: Brandon- Thanks for the question. You will need a winch mount bumper like the ARB Bull Bar that you can find here http://jo.my/sg5z03 in order to mount the Smittybilt XRC-12K WINCH GEN2 to your 2006 Dodge Ram 1500 SLT

A: Hello Grubby, Thank you for the question. yes, this winch will fit your vehicle application.

A: JMC- Thank you for your question. The Winch rope for the Smittybilt XRC-9.5K Waterproof Winch Gen2 is 93.5 feet and the control cable is on a 12 foot lead.

A: B- Thanks for the question. The Smittybilt XRC-9.5K Waterproof Winch Gen2 does have a clockable freewheel handle section. The solenoid can be moved but depending on where you need it you may have to modify the mount.

A: Lee- Thanks for asking. You can find them here on Smittybilt's site http://www.smittybilt.com/gen2_winches.html

A: Ben- thanks for the question. This Smittybilt XRC-9.5K Waterproof Winch Gen2 has an IP67 rating for water resistance. You can find the definition of this here http://jo.my/vwe1pc

A: Pinky- Thanks for the question. The IP68 rating can be explained here http://jo.my/vwe1pc and will prevent damage to the winch in actual submurged water crossings.

A: Hello GT, Thank you for the question. Smittybilt offers the M1 Dodge Truck Winch Mount Front Bumper with D-ring Mounts and Light Kit Part Number: S/B612800

A: Hello chevy2003, Thank you for the question. Yes, the Smittybilt XRC-12K WINCH GEN2 will fit your vehicle application.

A: Hello vitorinfias, Thank you for the question. The Smittybilt XRC-9.5K Waterproof Winch Gen2 comes with a roller fairlead.

A: Hi tacobender6 The conversion is simple you must MUST change the fairlead to a non roller style to prevent damage to the rope. the roller fairlead when the rope is pulled to the corner it has a sharp angle that it must conform to that it will actually fray the rope.http://jo.my/1yb7ze Thank you

A: Hello Gene, Thank you for the question. You will need the Smittybilt XRC Logo Winch Cover Part Number: S/B97281-99

A: Hi Bryan Yes this winch will power in and out. Thank You

A: Hi Jerry The Road Armor 60504B bumper is designed to fit all the Warn large frame winches. the dimensions of this winch are very similar to the warn 16.5 winch. we have not test fitted this as of yet as they are not in stock until end of April. Thank You

A: Quinn- Than you for your question. The Battery leads for the Smittybilt XRC-9.5K Waterproof Winch Gen2 are 2 gauge. You will need a batter of at least 650 cca.

A: Hi ramrod These winches are not made in the USA they are imported from China Thank You

A: Hello Sandman, Thank you for the question. Yes, the Smittybilt XRC-9.5K Waterproof Winch Gen2 S/B97495 will fit your vehicle application.

A: Lukaz- Thanks for the question. The Smittybilt XRC-17.5K WINCH GEN2 will not fit in the Fab Fours DR09-N2650-1 Dodge 1500 winch mount.

A: RM- Thank you for your question. The Smittybilt XRC-9.5K Waterproof Winch Gen2 is the next generation in the smittybilt winch line. Its water proof and is 9.5 is higher speed, higher hp and higher line pull. It is an excellent value.