Smittybilt SRC Front Bumpers

A: No you don't need to move the pump.

A: No, you do not

A: There is no mention of the "pump" in the instructions: https://www.4wheelparts.com/sku/Smittybilt/standard/SB76744.pdf

A: bolt hole on the arch is 7 3/4" center to center 9 1/2" outside to outside tabs, a light bar of 12" to 16" would look good. anything wider may look odd JMO

A: The arch is 7 3/4", the light tabs are set up for round or cube style lights.

A: I use the OEM bulbs and have had no problems. My bumper came without fog light bulbs.

A: OE factory JK fog lights will work.

A: metal, welded and powder coated same as the number 

A: I called the company and they said yes. One of the very few that indicated it was rated for towing. Don't take my word for it, call them. I have been using the bummer and towing my 2007 Jeep 2-Door with no problems.

A: For Technical Support/Warranty Information please call 310-762-9944 Shipping Measurements: L: 58.0 x W: 21.0 x H: 16.0 # 92.00

A: No issues or problems w/ the Mountain Edition.

A: WILL ONLY FIT WITH FACTORY HALOGEN LIGHTS NOT THE FACTORY LED LIGHTS

A: Unfortunately not that we offer. Will have to cut and splice in new wire to extend.

A: Yes, the bumpers are rated well beyond what one would see in a normal towing scenario.

A: 58" Length, 21" Width, 16" Height, 92 lbs weight

A: 22.9” from the bottom of the bumper to the top of the bull bar.

A: No drilling - all bolt on installation. The plate has welded nuts and the winch has a nut on the inside of the mounting feet as well.

A: Yes - the bumper has d-ring mounts for flat towing.

A: Yes, the bull bar does lean forward more than 75mm from the mounting point.

A: 3/4"

A: Hello Andy, Yes, that winch plate will fit this bumper. Thank you for the question.

A: Hello Austin, This is a direct bolt-on installation for your vehicle application. No drilling is required. Thank you.

A: Thanks for the inquiry Simon, the Smittybilt SRC Front Stinger with D-ring Mounts in Textured Matte Black part # S/B76521 you can mount a winch with the bracket use part # S/B2802.

A: Hello Gravey7777, yes, that winch will fit within this bumper. You will also need to purchase a winch mount plate to install said winch. Thank you.

A: Hi Mark The S/B76721 can be used in conjunction with S/B87450 Tow Bar Kit.This Smittybilt Tow Bar Kit has the mounts with it that will mount right to the D-Ring mounts on the bumper. The Tow Bar Kit even comes with the safety chain. I hope this was helpful. Thank You Jon Snyder 4Wheelparts

A: Hello Coy, the Smittybilt SRC Front Stinger with D-ring Mounts in Textured Matte Black part# S/B76521 is a front bumper and stinger in one unit. Thank you for your inquiry.

A: Thanks for the question. Those are called dimpled died holes. They put those in the steel to add strength and minimize the amount of steel used. It makes the steel more ridged/ stronger. Thank you.

A: Yes the Smittybilt SRC Front Stinger with D-ring Mounts in Textured Matte Black is a direct bolt on part. Hope this helps!

A: Thanks you for your inquiry NC. The Smittybilt SRC Front Grille Guard Bumper with D-ring Mounts will work with Smittybilt PART NUMBER S/B2803

A: Hello Alex, The Smittybilt SRC Front Stinger with D-ring Mounts in Textured Matte Black will work on your Jeep TJ with winch plate part number S/B2802

A: Hello Shawn, the Smittybilt SRC Front Stinger with D-ring Mounts in Textured Matte Black part# S/B76521 is compatible with a winch. Thank you for your inquiry.

A: Gerald- Thanks for the inquiry. The 3/4" D-Ring is the largest Smittybilt recommends for the SRC Front Grille Guard Bumper with D-ring Mounts

A: Noah- Thanks for the inquiry. You will need to relocate your factory go lights from the original bumper to the Smittybilt SRC Front Grille Guard Bumper with D-ring Mounts.

A: Hello Jsjsj, Thank you for the question. The Smittybilt SRC Front Grille Guard Bumper with D-ring Mounts will replace the factory bumper.

A: Bolt- Thanks for asking. The Smittybilt SRC Front Grille Guard Bumper with D-ring Mounts sticks out about 24 inches from the grille.

A: Alex- Thanks for asking. The Smittybilt 2803 Winch Plate will work with the Smittybilt SRC Front Grille Guard Bumper with D-ring Mounts

A: Zeki- Thanks for the question. Yes the Smittybilt SRC Front Grille Guard Bumper with D-ring Mounts will fit your 1992 Jeep Wrangler YJ

A: Thank you for your question. The Smittybilt SRC Front Grille Guard Bumper with D-ring Mounts part number S/B76721 weighs in at 77 pounds

A: John- Thanks for the inquiry. The Smittybilt bumpers come from one of two factories depending on production needs, one in Southern California and one overseas.

A: Bob- Thanks for the question. I would recommend the Smittybilt winch plate here http://jo.my/ue93g to go with your new Smittybilt SRC Front Grille Guard Bumper with D-ring Mounts