Smittybilt M1 Front Bumpers

A: The d rings are only used to pull stuff during emergencies usually when off-roading. Using the d-rings for towing on the road is dangerous because someone needs to be on the other vehicle holding the brakes by keeping tension on the chains/straps during the entire trip (hills/stops/etc). Get a tow hitch with a ball to properly tow anything on the road. 

A: Ring on the Bumper are incredibly sturdy. I’ve used them for recovery, but I am not sure about for being towed. Might be a question for the manufacturer.

A: If you ensure that everything is torqued to spec you should be just fine. I’ve had no problem pulling or getting pulled by the d-rings on my bumper. 

A: I don't know about that. But the front bumper bolts are too short. buy some at least 1" longer and it will be much faster install.

A: It took me like 6 weeks and 10 phone calls to get mine. They said it was going to ship within 3 days of ordering. 

A: Heavy. Smittybuilt has it listed as 240lbs. Good thing it comes in two pieces. Still, I was able to install it myself with the outer shell balanced on my floor jack. I also upgraded to 700lb springs on my struts to handle the extra weight.

A: On my 2007 they are square.

A: I purchased this for my 08 Dodge Ram, lights were square and you can adjust the gap during installation along the top of the bumper.

A: Smittybilt M1 Truck Bumper Light - Part Number: 612800-01 and Smittybilt M1 Truck Bumper Amber Fog Light - Part Number: 612800-02

A: Please give Smittybilt a call Toll Free: 888-717-5797 or Email: info@smittybilt.com

A: We have a 2007 and so far left that part off . as it did not seem necessary.

A: If you watch any YouTube videos on any bumpers, you’ll see it’s inevitable. You’re going to have to move the washer bottle. There are a few aftermarket options.

A: The Smittybilt M1 Toyota FJ Cruiser Winch Mount Front Bumper with D-ring Mounts and Light Kit part# S/B612850 will fit the 2007-15 Fj cruiser, will fit the Trail Teams Special Edition .

A: I would think so. I installed the smittybilt 17.5k version on mine. Fit with plenty of room. Pretty simple install. I balance the entire combination on a floor jack and with one extra person, installation was pretty smooth.

A: These are accent trim pieces.

A: Correct, these are trim pieces.

A: It should.    I have one on my 08 f250.   I think the front frame measurements are the same 

A: The Smittybilt M1 Ford 150 Winch Mount Front Bumper with D-ring Mounts and Light Kit - 612833 is not set up for tow bar hookup.

A: Yes it will fit. It accommodates up to 12k winches.

A: There are no pre-drilled holes on the top of the bumper for lights. However, this can be done after purchase, just have to use some touch-up paint to prevent rust.

A: No it will not fit.

A: Yes it can fit a 17.5k winch.

A: Yes it comes in black as well. Part number 612802.

A: Unfortunately this front bumper does not have sensor mounts. The turbocharger is under the hood connected to the exhaust manifold. The bumper does not affect this. If you mean the inter-cooler, It's about the same as with the factory bumper

A: Hey Jason, We need a little more info about your setup to get you the correct bumper. Please call our sales line Toll Free: 1-877-474-4821 Thanks!

A: Hello Doug, This Smittybilt M1 Front Bumper does not come with the D-rings/shackles. It has built in mounts for 2 D-rings/shackles.

A: Hello Red, this Smittybilt M1 Front bumper is specifically designed for a 2007-2011 Toyota FJ Cruiser. It will not work with any other vehicle.

A: Hello jeremiah, With a few mild modifications, this will work with a plow. Thank you for the question.

A: Thanks for the inquiry Mingo, the Smittybilt M1 Front Bumper part # S/B612800 this is a bolt on application.

A: Hello Rob, Sorry, Smittybilt does not offer this bumper without powder coating at this time. Thank you.

A: Thanks for the inquiry Dan, the Smittybilt M1 Front Bumper part # S/B612821 this part fits 07.5-2013 Chevy HD 2500-3500.

A: Hello Tom, The shipping weight is 343 lbs. Only thing required to make this bumper legal to California is a license plate. I hope that helps. Thank you.

A: Hello fastskull, Yes, the Smittybilt M1 Front Bumper S/B612821 will fit your vehicle application. Thank you.

A: Hello Kent, Technical Details: Fits 2007 to 2010 Chevrolet 2500/3500 HD. Thank you.

A: Thanks for the inquiry Panhandleslim65, the Smittybilt M1 Front Bumper part # S/B612800 the shipping weight is 340 pounds.

A: Hi Jerry The S/B612821 will fit your 2013 4X4 Chevy 2500HD and it is rated to handle up to a 17,500lbs winch. Thank You for your question. Jon Snyder 4Wheelparts

A: Hello Charles, The Smittybilt M1 RAM Truck Winch Mount Front Bumper with D-ring Mounts and Light Kit S/B612802 installs with provided bracketry and hardware. Thank you.

A: Tony, the lights are included with the bumper. Thanks for the question.

A: Thanks for the inquiry Nick, the Smittybilt M1 Front Bumper part # S/B612821 this bumper does come with all lights and hardware to install on the vehicle.

A: Thanks for the question. Yes, this bumper will come with the bumper lights. Thank you

A: Hello Abdu, the Smittybilt M1 Toyota FJ Cruiser Winch Mount Front Bumper with D-ring Mounts and Light Kit part# S/B612850 will fit the 2007-15 Fj cruiser. Thank you for your question.

A: Hello there, the Smittybilt M1 Toyota FJ Cruiser Winch Mount Front Bumper with D-ring Mounts and Light Kit is available here in Los Angeles, Please call me @ 800 337 9005 ext:5923 if you would like to please the order. Shop with us anytime, on your schedule. Browse 4WheelParts.com, call our customer service center, or come visit us in one of our stores. You can even save on shipping costs by shopping online and picking your order up in a store. No matter which method you prefer, we’re ready to help with excellent parts, advice, and service.

A: Hello there, the Smittybilt M1 Front Bumper is a nice bumper but yes you'll have to move the winch into the bumper it self. Shop with us anytime, on your schedule. Browse 4WheelParts.com, call our customer service center, or come visit us in one of our stores. You can even save on shipping costs by shopping online and picking your order up in a store. No matter which method you prefer, we’re ready to help with excellent parts, advice, and service.

A: Thanks for the inquiry Jason, the Smittybilt M1 Front Bumper part # S/B612800 will house most mid frame and large frame winches, the largest winch it can hold is a 16.5 TI from warn.

A: Charles,Thanks for the question.Your factory bumper does come off.This is full bumper replacement.

A: Gio,Thanks for the question.Part #S/B612802 Smittybilt M1 RAM Truck Winch Mount Front Bumper with D-ring Mounts and Light Kit costs 1299.99 plus 115.32 for shipping.

A: Hello, The Smittybilt M1 RAM Truck Winch Mount Front Bumper with D-ring Mounts and Light Kit will allow you to plug direct to your factory lights.

A: It only fits 2010-2012 smittybilt is still working on one for the 2013 at this time.

A: Thanks for the inquiry Hollywood, the Smittybilt M1 RAM Truck Winch Mount Front Bumper with D-ring Mounts and Light Kit part # s/b612802 will NOT fit a 1500.

A: Dr inzunza,Thanks for the question.Part #S/B612802 Smittybilt M1 RAM Truck Winch Mount Front Bumper with D-ring Mounts and Light Kit will work with a Warn 12000 winch.

A: Pete, What most people do with the lights from the Smittybilt M1 Front Bumper is just splice them into the factory light harness. Its a pretty easy job. Hope this helps!

A: Hello TK The Smittybilt M1 Toyota Tundra Winch Mount Front Bumper with D-ring Mounts and Light Kit is in R&D and should be releasing so for retail sales.

A: Tim, The 1500 mega cab is a 2500 dodge 8 lug so the bumper should fit no problem as long as the front end looks the shame as the regular dodge 2500.

A: Jim, You can access the winch from the top of the bumper by the grill. The bumper weighs about 238lbs when shipped with packaging. Usually the factory skid plate hits the new bumper and will not work unless you modify it.

A: Hello George, the Smittybilt M1 Ford Superduty Winch Mount Front Bumper with D-ring Mounts and Light Kit does fit your vehicle. You would need part# s/b612831

A: Enfocus- Thank you for your question. The Smittybilt M1 RAM Truck Winch Mount Front Bumper with D-ring Mounts and Light Kit come powder coated from the factory. We do not sell them in plane steel

A: Cody- Thanks for the question. The Smittybilt M1 Toyota Tundra Winch Mount Front Bumper with D-ring Mounts and Light Kit will fit your 2012 SR5 tundra.

A: Kip- Thanks for the question. Smittybilt says this M1 RAM Truck Winch Mount Front Bumper with D-ring Mounts and Light Kit only fits up to 2012 Ram 3500

A: Hello PE, Thank you for the question. You will need the M1 Truck Bumper Clear Driving Light S/B612800-01

A: Mark- Thanks for the question. You can find the Smittybilt M1 RAM Truck Winch Mount Front Bumper with D-ring Mounts and Light Kit that will fit your 2009 Dodge Ram 3500 here http://jo.my/2gbw7w . Smittybilt does not offer these bumpers in bare metal.

A: Mark- Thanks for the question. This Smittybilt M1 Toyota Tundra Winch Mount Front Bumper with D-ring Mounts and Light Kit will not fit your 2014 Toyota Tundra SR5. I contacted Smittybilt and they have a M1 Bumper coming for the 2014 Tundra but it is about 120 days still available.

A: RJDowell- Thanks for asking. You would need a Smittybilt roller fairlead licence plate mount which you can find here http://jo.my/mhzn4g to put your plate on the M1 Front Bumper.

A: Thank you for your question Grant. The Smittybilt M1 RAM Truck Winch Mount Front Bumper with D-ring Mounts and Light Kit part number S/B612802 fits a 2010 to 2012 RAM 2500 & 3500. Smittybilt does not make a front bumper to fit your truck follow this link and make sure the correct vehicle has been selected to find what fits your truck http://jo.my/8bqaqr

A: The Smittybilt M1 RAM Truck Front Bumper is only available in Black. It will not affect your air bag sensors as they are mounted on the frame rail, not the bumper. According to smittybilt a 16.5k winch will fit.

A: This Smittybilt M1 Front Winch bumper will fit your 2013 Tundra.