A: Per Skyjacker this pitman arm is for the following: 67-91 GM 3500 Pickup 4WD – For Open Knuckles Only; For 2.5-4 in. Lift 67-87 GM 1500, 2500 Pickup 4WD – Must Have 3-Bolt Steering Knuckle; For 2.5 in. Lift 67-91 GM 1500, 2500 Blazer, Jimmy, Suburban – Must Have 3-Bolt Steering Knuckle; For 2.5 in. Lift Please call our sales line toll free at 1-877-474-4821

A: hello no it is for a 2.5 to 4 inch lift. You should use an steering arm on the knuckle for a 6 inch kit. you can use the SKY CA100 or the EXP GM400 Thanks

A: Hello Chevy, You will reuse the factory bolt. Thank you.

A: Hello Chris, Yes, the Skyjacker Pitman Arm will have a spline (grooves) that matches the vehicles steering gear box. Thank you for the question.

A: Hello Goose, The Skyjacker Pitman Arm are available for your year truck. Please contact your wholesale representative for pricing.

A: Hello Travis If you are doing a crossover steering you will need a pitman arm that is splined for the 2wd box. You can use the Skyjacker SKY FA300

A: Hello Kevin Yes it will make a big improvement in the turning radius. Once you install it leave the drag link off. Then turn the steering wheel lock to lock counting how many turns it takes and go back exactly half way to center the steering box. Now adjust the drag link to fit into the pitman arm.

A: Hello Yee Yee, the Skyjacker Pitman Arm part# SKYCA50 will not fit your vehicle. You would need a steering arm part# Expgm400. Thank you for your inquiry.

A: Hi Bucket Trucker This arm will drop the front of your drag link 2 full inches you will need to see if that is enough as i do not know if you have a 4" steering arm or a rare 6" steering arm. Thank You

A: Remdum- Thank you for your question. The Skyjacker Pitman Arm SKYCA50 will fit your truck with power steering.

A: Hello Lee, Thank you for the question. The Skyjacker Pitman Arm SKYCA50 is the only pitman we offer at this time.

A: Hi Sully The Skyjacker CA50 will assist in reducing the angle on the steering system with your 12" lift on your 1989 K5. With 12" of lift you should consider a cross over steering system if you wheel your truck. Thank You

A: Hi Jim I do not have the arm here were i am and do not have that information. Most of the cross over steering setups i have seen use a Chevrolet drag link rod end or a tie rod end. I know of no off the shelf arm that will fit these ends. most arms that are advertised to fit this have been reamed to fit. you van buy a tie rod reamer at your auto parts store for about $30.and then ream the arm your self. I am assuming that you are using a 2WD Chevy steering box. the arms that fit the Chevy steering box come off of 1979 Ford F-150s Thank You

A: Hi Chris The 2.5 drop pitman arm will help take the angle off of the drag link some but you will still need to use it with a 4" steering arm because it is not enough drop for a 6" lift. thank You

A: Hi HB The Skyjacker CA50 is a pitman arm that goes on the steering box and is good for 2.5"-4" lifts where the Pro Comp arm is a steering arm that goes on the steering knuckle of the axle and is good for 4"-6" lifts. both can be combined for 6"-8" lifts Thank You

A: Hi Austin Yes the Skyjacker CA50 pitman arm will fit your 1986 GMC with non cross over steering factory style. Thank You

A: Thank you for your question. The Skyjacker Pitman Arm part number SKYCA50 will work for your 1989 Chevy K5

A: Matt, The Skyjacker Pitman Arm SKYCA50 is the correct fit for a 1991 Chevy Blazer.