Rubicon Express Sway Bar Disconnect Sets

A: Not sure, I dealt directly with RE...They forgot to send them out or something and just sent me a new complete set. I think it originally was a set of two tho

A: Sold as each.

A: The standard 5/8 hourglass style do not fit. They are a ball style. 

A: Bushings are standard 5/8” hourglass shock bushings. You can use any replacement shock bushings, rubber or urethane.

A: Mine are falling apart as well. Looks like we have to buy new ones every 3 months... Junk

A: Not at this time. You will need to replace the entire RE1131 kit.

A: Part # RE1130 Fits 1993 to 1998 Jeep ZJ Grand Cherokee with 2 - 4 Inch Lift

A: They should fit.   I have a 3.5in lift and had to extend them.   

A: The Rubicon Express Sway Bar Disconnect Set - RE1133 (Adjustable from 8” -11”)

A: Steel

A: The weld on tab is only for holding the link when disconnected from the axle. You do not have to use the weld on tab to hold the end link up and out of way, you use zip ties.

A: This is one pin.

A: Yes

A: Yes you have to order the JKS quicker disconnect spherical bushings

A: No, RE1130 for XJ 2-3.5” lifts. You need RE1131 for XJ 4.5-5.5” lifts.

A: Cano04, we have different options. Here are some links for you to look at some of our Rubicon Express and Pro Comp end links. Rubicon Express Sway Bar End Links - https://www.4wheelparts.com/p/rubicon-express-sway-bar-end-links/10346 Pro Comp Suspension Sway Bar End Link Kits - https://www.4wheelparts.com/p/pro-comp-suspension-sway-bar-end-link-kits/9506

A: No you do not.

A: These will fit 1976 to 1995 YJ Wrangler and CJ models with 0-6" lift.

A: Yes but this is just the pin.

A: Hello aj, Rubicon Express Sway Bar Disconnects Set W/10" Center YJ 4.0"+ will work on a YJ with a 4" lift and up.

A: Hello Gone, This will require some drilling to installation. Thank you.

A: Hello bruno, Yes, this will fit your vehicle application. Thank you.

A: Hello Yes they have the pins to lock the bar up out of the way. Thanks

A: No they just bolt on using regular wrenches.

A: Thanks for the inquiry mooch, the Rubicon Express Extreme-Duty Sway Bar Disconnects part # R/ERE1130 will work for your 98 TJ with 0-2 inches of suspension lift, body lift will have no effect.

A: Hello Wal, Thank you for asking. The Rubicon Express Extreme-Duty Sway Bar Disconnects will allow you to have better articulation when you're out wheeling. If you do not plan to go off road, your factory sway bar end links will work just fine.

A: Bobby- Thanks for the question. The Rubicon Express Sway Bar Disconnects are designed to work for the front and are not applicable for the rear.

A: Hello For the YJ and CJ they are a direct fit. If you have a TJ ZJ XJ you will need the adapter brackets to make them fit.

A: Hello Naseer, Thank you for asking. The Rubicon Express Sway Bar Disconnects part# R/ERE1131 will fit a 1997 Jeep Wrangler that has a 2.5" - 5" lift.

A: Hello Yes they work on the Rubicon's also if they are lifted a minimum of 2.5 inches.

A: Josh, Thank you for asking. I could not locate install sheets anywhere, Please call Rubicon Express and they should be able to provide that for you. (866)533-7706

A: Fish, Yes these sway bar links will fit with your 2.5" kit

A: Hello They will work if you have aftermarket quick disconnect end links on your Jeep. The stock end link have a tie rod type end that can't be replaced.

A: Hello Matt, the Rubicon Express Sway Bar Disconnects part# R/ERE1131 will fit an xj with a 4-5.5" lift. They currently do not offer any for a stock height xj. Thank you for your inquiry.

A: Derf, Thanks for the question. Rubicon Express Sway Bar Disconnects part # R/ERE1132 is made for a 2.5" to 6" lift.I recomend contacting Rubicon express to get measurements & compare to what you have with your Rancho 2' lift.

A: Joe- Thanks for the question. Rubicon Express Sway Bar Disconnects part number R/ERE1132 will not work with stock height.

A: Hello Harold, Thank you for the question. The Rubicon Express Sway Bar Disconnects R/ERE1131 will fit a 2.5" to 6" suspension lift kit.

A: Myke- Thank you for your question. The Rubicon Express Sway Bar Disconnects are designed to work in the front only.

A: Joey- Thank you for your question. The Rubicon Express Sway Bar Disconnects part number R/ERE1132 will fit a range of 2.5 to 6 inches of lift.

A: Hello Patt, Thank you for the question. The Rubicon Express Sway Bar Disconnects R/ERE1131 will fit a 2.5" to 6" suspension lift kit.

A: The Rubicon Express Disconnect uses a R/ERE1187 for the axle pin you can find it here http://jo.my/ecznha