These are the original, most proven, and only patented Rear Overhead Angle Bars available for your Jeep Wrangler TJ/LJ with sound pods. These give you added protection and strength behind your factory cage hoop. These install in minute using our patented locking collars and give you a factory look. Our proprietary locking collars are arguably the safest and most secure way to not only strengthen your Jeep's cabin but also provide you and your passengers the peace and mind that comes with a premium cage system. No other bolt-in cage comes close to the fitment, quality, and durability of our system.
Put mine on 14 years ago. It came bare so i used some spray paint before installing. I noticed a slight stiffening in cornering right away. The lift i had was fairly soft. I use it all the time. You can hang almost anything from it. High lifts. Shovels. Currently i use paracord and carabiners to secure water jugs. Also use it to connect a tarp for shade. Oh yeah and for rear protection.
By LrbLbc from CA
nice way to reinforce roll cage
By ironman from mexico
Did not fit
Have the front rock hard roll cage. It fit fine. Finally got around to the rear. It's supposed to match up to the front clamps. The directions say you have to pull the bars together to get the across the rear bar to fit. Not the case. The bar was too long and the angle bars wern't even close. They were about 3 inches too long. I tried to pull the bars apart and stopped after i broke 2 of the bolts. I boxed it up and returned it. don't waste your time.
By Dan from Jacksonville florida
nice cage addition
Fairly simple concept that is easy to install with great quality welds
By Joe from MA
Reinforce your Jeeps roll cage
Strengthens my TJs roll cage. I you use a safari top this can reduce or eliminate the flapping noise at the rear.
I accidentally rolled my TJ and the straight across bar did its job.
By RW Bumper from Torrance, CA
Easy to install
Easy to paint, easy to install, I can still recline my seat slightly.
I feel safer in the jeep with hardrock bars attached.
With 4 or 5 point seatbelts the shoulder belt attachment points
are critical to avoid spinal compression injury.
Using this bar makes attaching the shoulder belt to a safe location
The part number listed here is RH1001-F, which is the correct part number for a 2005 TJ with sound pods. The picture is the straight bars. Just making sure the part I would receive is the right one for the part number and not what is pictured. This will fit my TJ with sound pods right?
Bill from Selinsgrove, PA on
Yes the part is correct the picture is wrong. Rock Hard sends us the photo's to use and they don't have the 2004 up picture.
Rody from Selinsgrove, PA on
Was this bar intended for stock application? Will it fit on stock rollbar? Is welding required?
Nick from Kahalu'u, HI on
Yes this is designed to attach to the factory rollbar. Under product specs it does say it is a bolt in installation.
Rody from Kahalu'u, HI on
I am looking for a harness bar for a 1942 jeep that has a roll bar that is approx. 54" wide. Can you recommend one? I would prefer a bolt on but would go with a weld on if necessary.
thomas from Palm Springs, CA on
Hello thomas and thank you for your question! Rock Hard 4x4 Parts Harness Attaching Bar is a weld on application and is stronger then the bolt on.
The concept for Nebraska-based Rock Hard 4x4 Parts was hatched back in the 1980s and evolved from DIY cage installation to a full-service manufacturing facility. Employing state-of-the-art CNC machining centers, outstanding craftsmanship and laser cut precision, Rock Hard takes the bolt-in design of bumpers, skid plates, cages and sliders to the next level. Their patented locking collar distinguishes itself in the aftermarket industry and all of their exterior products make off-roading in Jeeps safer and smoother. Protection is paramount on the trail and Rock Hard's products are easy to install, affordable and exude superior style. Shop Rock Hard 4x4 Parts Now