Revtek Spacer Lift Kits

A: Correction KIT # 440 – 2.5″ FRONT / 1.5″ REAR SPLIT SPACER SYSTEM (NO REAR AIR)

A: This is a 2 1/2" front lift and a 1" rear lift to level the Sequoia out using spacers.

A: I have the same lift on my 05 excursion and run 37's with no rub

A: Remo- Thanks for the question. The Max tire size for the Revtek 6 Inch Lift Kit is a 35 x 12.5.

A: KIT 440 – 2.5″ FRONT / 1.5″ REAR SPLIT SPACER SYSTEM (NO REAR AIR) Shocks are not required however, they are recommended. https://www.4wheelparts.com/sku/Revtek/standard/INST-440.pdf

A: This will fit your 2007 Jeep Liberty sport and you reuse the stock shock.

A: No, the rear u-bolts will be different.

A: Yes it will fit.

A: The REV442 is a spacer lift. It will clear 33” tires.

A: We don't know how much room you have in your garage to answer this. You can run up to 33" tires and this will add inches to your overall vehicle ride height. It depends on how much clearance you have.

A: Kit is designed for single rear wheel axles. Front part of kit will work. Rear u-bolts will need to be changed.

A: Yes, this will fit your vehicle.

A: Drop pitman arm is included in this kit.

A: Hello Christian, All lift kits with the exception of a coilover or ride height adjustable strut will ride stiffer than the factory height. This is why we recommend a coilover or ride height adjustable strut. We do offer active military discounts but you will need to call in and speak directly with a salesman for pricing. Thank you.

A: Hello Andy, The backspace of the wheel would need to be between 4" and 5". Hard to confirm without measuring.

A: Thanks for the inquiry thecargal, the Revtek 2.5 Inch Lift Kit part # REV437 a 17 inch wheel will run fine with this lift.

A: Hello Henk, This lift will allow you to run a 285/70 tire. This will help correct the front end sag. Thank you.

A: Hello Trey, Yes, this will fit your vehicle application. Thank you for the question.

A: Hello Bob, Yes, you will need longer rear shocks when installing the Revtek 2.5 Inch Lift Kit Part Number: REV440. Thank you for the question.

A: Hello Marion and thank you for your question! Revtek 2.5 Inch Lift Kit is not at the Dallas store, but can be sent to the store.

A: Hello Mike The REV6741 will fit your 2014 F350 Dually as long as it is a 4X4. The u-bolts WILL NOT fit the larger axle tubes of your Dually Rear End. The rear u-bolts will need to be custom made. If you have a Franklin Truck Parts in your area they can bend up u-bolts. Thank You for your question. Jon Snyder 4Wheelparts .

A: Hello John, Yes, the Revtek 2 Inch Lift Kit REV840 will fit your vehicle application. Thank you.

A: Hello Willramit, No modifications to the exhaust, drive shaft or transmission are required with this kit. Thank you.

A: Hello Patrick, Yes, the Revtek 3 Inch Lift Kit REV425 will fit your vehicle application. Thank you.

A: Hello tony, We suggest upgrading the rear shocks when installing the Revtek 3 Inch Lift Kit REV430

A: Hello John, Thank you for asking. The Revtek 3 Inch Lift Kit will work on a 2012 4runner

A: Hello Stev, the Revtek 2.5 Inch Lift Kit part# REV437 would require an alignment when done. Thank you for your question.

A: Hello BigRedDodge and thank you for your question! Revtek 6 Inch Lift Kit would work with a Superlift 6" lift with the proper fabrication.

A: Hello, the Revtek 3 Inch Lift Kit part# REV425 can be installed at home using basic tools. Make sure to get an alignment when finished. Thank you for your inquiry.

A: Hello Charles, The Revtek 6 Inch Lift Kit will allow you to run a 35"tire.

A: Hello Goose IV from Georgetown TX and thank you for the inquiry on the Revtek 4.5 Inch Lift Kit. I am sorry but the factory shocks will not work with this lift kit, you will need to replace them since you will be lifting your vehicle. This lift kit comes complete with the appropriate shocks for your vehicle. so you will not have to buy them in addition to the kit. Here is the link to get you back to the ordering page: http://jo.my/cda1ti.qrcode

A: Hello, unfortunately we do not have the instructions or diagrams you are looking for. Please contact Revtek direct for this info. 503-659-1650. Thank you for your question.

A: Thanks for the inquiry JR, the Revtek 6 Inch Lift Kit part # ev7106d-3 will only fit a 2003-2008 Ram 2500.

A: Thanks for the inquiry derek, the Revtek 3 Inch Lift Kit part # rev426 we will recommend the rear shock upgrade use part # BIL24-186728.

A: Hello Gunite, Thank you for asking. The Revtek 2 Inch Lift Kit will allow you to go up to a 32" tall tire. 285/75/16 with factory wheel will do just fine.

A: Hello Crooks85, Thank you for asking. With the Revtek 2.5 Inch Lift Kit you should be able to run 33 inch tires with a wheel is at least 18 inches and has a backspacing of 4-6 inches. Might require trimming.

A: Thanks for the inquiry Toy truck, the Revtek 3 Inch Front Suspension Lift Kit part # REV426F is only for the front you can use part REV423A to get the kit with a rear lift.

A: Thanks for the inquiry bulldog, the Revtek 3 Inch Front Suspension Lift Kit part # REV425F is the front only you can use part REV425A the includes the rear.

A: Hello chris and thank you for your question! A 16" aftermarket wheel will not clear the brake calipers. The 16 " Toyota wheels are made to fit over the calipers. A 3" lift will work with the 5100 struts and shocks with the strut spacer in the front and a block or add a leaf in the rear. I hope my answers help get 4 Wheel Parts your business.

A: Daveq- Thanks for your question. The Revtek 3 Inch Lift Kit with Lift Blocks will fit your 2011 4wd Access Cab TRD TX Pro- Yes you can run your 285 / 75 / 16 with it. Please contact your local 4 wheel parts store for a quote on installation and scheduling.

A: Cabix81- Thanks for your question. The Revtek 3 Inch Lift Kit with Lift Blocks will fit your 4wd 2014 Tacoma.

A: Thanks for the inquiry Davis, the Revtek 3 Inch Lift Kit part # REV431 is incorrect, you'll need part # REV413 for a 2004 Toyota 4 runner.

A: Hello there, the Revtek 4.5 Inch Lift Kit come with front and rear shocks. No need to get any more parts. Shop with us anytime, on your schedule. Browse 4WheelParts.com, call our customer service center, or come visit us in one of our stores. You can even save on shipping costs by shopping online and picking your order up in a store. No matter which method you prefer, we’re ready to help with excellent parts, advice, and service

A: Hello Bill. The Revtek 3 Inch Front Suspension Lift Kit, part # REV425F does not require new front struts. Thank you

A: Thanks for the inquiry koa, the Revtek 3 Inch Lift Kit with Lift Blocks part # REV426 will require an aftermarket wheel with approximately a 4.5 inch backspace to run a 285/70/17 tire.

A: Jim, Thank you for asking. Revtek 3 Inch Lift Kit with Add-a-Leafs part# REV426A will work with Factory rear shocks.

A: Hello there,with a lot of the trucks coming out with extra packages it dose get a little confusing ordering the right lift. The Revtek 3 Inch Lift Kit part number REV432 is designed to work on your 2011 Limited Toyota 4Runner with the XREAS system. Shop with us anytime, on your schedule. Browse 4WheelParts.com, call our customer service center, or come visit us in one of our stores. You can even save on shipping costs by shopping online and picking your order up in a store. No matter which method you prefer, we’re ready to help with excellent parts, advice, and service.

A: Hi Robert Revtek 3 Inch Front Suspension Lift Kit, REV426F We can order the rear kit for you. We will have to contact the manufacture and special order the rear kit individually. Thanks for the question.

A: Hello Jack, the Revtek 3 inch lift kit is a 3" solid spacer lift. So you will end up with 3 inches taller in the front than where your truck currently sits. Thank you for your question.

A: James- Thanks for the question. The Revtek 3 Inch Front Suspension Lift Kit is a front only lift kit.

A: Dakota, Thank you for your question. On the Revtek 6 Inch Lift Kit part # REV717 does require you to have a 6" lift already installed on your vehicle before you can install this.

A: Hello Shaft, Thank you for the question. Yes, you will need a strut compressor. Here is a direct link to the installation instructions http://www.revtek.com/wp-content/uploads/2014/06/INST-435.pdf

A: Hello 3R3, Thank you for the question. Yes, installation will require a coil spring compressor.

A: Hello Chris, Thank you for the question. Yes, the Bilstein 5100 series Ride Height Adjustable shocks can be used with this kit.

A: Tony- Thanks for the question. Both rev tek kits 441 and 442 will fit 08-14 sequoia. The difference between the 442 and the 441 is a complete lift, front and rear. The 442 is a level kit, front only.

A: Pinky- Thanks for the question. The Revtek 4.5 Inch Lift Kit is a lift level kit. The Rear lift block in the kit is a 5 inch block that replaces the factory 3 inch block.

A: Hello Andy, Thank you for the question. Yes, this kit will fit and level your vehicles ride height. Revtek recommends a 35x12.50 tire size with this kit installed on your vehicle.

A: Hello Chuy, Thank you for the question. The Revtek 3 Inch Lift Kit will fit a 33 x 12.50 tire with not rubbing.

A: Hello Brewski, Thank you for the question. The Revtek 4.5 Inch Lift Kit Part Number: REV6741 does not come with shocks.

A: Hello Jean, Thank you for the question. The Revtek 4 Inch Lift Kit Part Number: REV6004 does not come with a pitman arm and the rear leaf springs are factory width.

A: Chris- Thank you for your question. The Revtek 6 Inch Lift Kit does come with front and rear shocks.

A: Shane- Thank you for your question. Yes the Revtek 6 Inch Lift Kit will fit your 08 ford F250 Diesel.

A: Paul- Thank you for your question. The Revtek 6 Inch Lift Kit uses 5 inch blocks in the rear and a add a leaf. The yield in the rear is pretty predictable as 6 inches. If that is too much for you can leave out the add a leaf. Putting the hitch 6 inches up will cause your trailer to sit nose up. You can get a drop hitch found here http://jo.my/vwtfn2 .

A: Hello Crusher, Thank you for the question. This kit does not include shocks.

A: Fordboy- Thank you for your question. The Revtek 3 Inch Lift Kit with Lift Blocks is a fixed kit. We can not change the content of this kit. We do have a 2 inch lift block for your Toyota Tacoma found here http://jo.my/yzwvq1

A: Adam- Thank you for your question. The Revtek 4.5 Inch Lift Kit is an excellent kit. I would recommend this kit. You should check your ball joints and drive shaft universals when installing a lift kit.

A: Hello Taco Man, Thank you for the question. Yes, this kit will allow you to ru nthe XD Addict 17x9 wheels. You will need longer rear shocks with this kit installed. You space/retain the factory front struts. You can also run the factory wheel and tire combo for a good amount of time after installation of this kit. This kit will not effect factory towing specs. Please Note: The factory rear Tacoma leaf springs are on the weak side and we suggest adding a rear air bag helper kit if you plan on doing any serious distance towing. All installation quotes will be provided by your local 4 Wheel Parts store.

A: Redsoxcruiser- Thank you for your question. The Revtek 2.5 Inch Lift Kit is not compatable for a 05 Sequoia limited with air ride suspension.

A: CT Thank you for question. The Revtek 3 Inch Lift Kit with Lift Blocks will relocate your front stock struts. I would recommend that you replace the rear shocks. I would recommend the pro comp es9000 found here http:\/\/jo.my\/z9tcce

A: Hello chrishollins33, Thank you for the question. Yes, the Revtek 3 Inch Lift Kit REV431 will fit the 2003 to 2009 Toyota FJ Cruiser. You can run a 32" tire with this kit installed.

A: Hi Chris This kit uses rear lift blocks in the rear and coil spacers in the front. you will receive all the necessary parts to properly lift your truck with out the need for additional parts, Thank You

A: Chuck- Thank you for question. The Revtek 3 Inch Lift Kit with Lift Blocks will relocate your front stock struts. I would recommend that you replace the rear shocks. I would recommend the pro comp es9000 found here http://jo.my/z9tcce

A: Jon- Thank you for your question. The Revtek 3 Inch Lift Kit does not require a Diff drop. It is the max lift kit you can install with out lowering the differential.

A: Staylo- Thank you for your question. The Revtek 6 Inch Lift Kit does come with radius arms. Part number RAF46.

A: Hello Kevin, Thank you for the question. Yes, the Revtek 3 Inch Lift Kit with Lift Blocks REV426 will lift the front of the vehicle 3" and the rear 1". This kit was designed for a level vehicle stance.

A: Hello Victor, The Revtek 2.5 Inch Front Suspension Lift Kit REV438F is a leveling kit. It only lifts the front of the vehicle. With this kit installed you can run a 33x12.50 tire. Thank you for the email. To run a 35" on the Toyota Tundra you will need a minimum of 4" of lift. That can be a combination of suspension and body lift or just suspension alone. Thank you for the email.

A: Hello Zack, The Revtek 3 Inch Lift Kit with Lift Blocks REV426 comes with a diff drop. Thank you for the email.

A: Hello nobleyleal, Here is a direct link to the instructions http://jo.my/3lruyy Thank you for the email.

A: Craig- thanks for asking. The Revtek 3 inch lift kit reuses your factory shocks. According to Revtek it will fit 5 lug.

A: JIm- thanks for asking. I would recommend the Pro Comp Pro Runner struts and shocks to go with the Revtek 3 inch lift on your 2009 Toyota Tacoma. You can find them here http://jo.my/pohy3g

A: Thank you for your question. The Revtek 3 Inch Lift Kit part number REV431 comes with rear shocks but not front. You should upgrade your front shocks if they are stock and have high mileage.

A: Thank you for your question. The total weight of the Revtek 2.5 Inch Lift Kit part number REV441 is 13 pounds

A: Thank you for your question. I just called Revtek and the Revtek 3 Inch Lift Kit part number REV570 does come with shocks and we will be updating the site.

A: Hello JJ, This part fits your vehicle: 2007 TOYOTA 4RUNNER SR5 4x4 with a Max Tire Size: 285/75. Thank you for the email.

A: Hello yota dude, With the Revtek 3 Inch Lift Kit with Add-a-Leafs REV426A installed you can run a max tire size of 33x12.50. Thank you for the email.

A: Hello Bubba, You will not need a coil spring compressor for this installation. The front spacers bolt on between the chassis and the strut/coilover shock. Average installation time on this kit is 4 - 6 hours. Thank you for the email.

A: Hello Zach, The Revtek 3 Inch Lift Kit with Lift Blocks REV426 max tire size is 285/75. Thank you for the email.

A: Hello Just Dave, Yes sir, the Revtek 3 Inch Lift Kit with Lift Blocks REV426 will fit the 2005 to 2012 Toyota Tacoma 4WD & PreRunner. Thank you for the email.

A: swampgravy, The Revtek Lift Suspension System Lift Kit REV431 allows for tires up to 285/75 max.

A: Hi Bubba The RevTek REV426 3 inch lift kit for the Toyota Tacoma comes with rear lift blocks and u bolts to lift the rear of the truck.

A: The Revtek lift kits 426 includes lift blocks and the 426A has an add-a-leaf rear spring.

A: The Revtek 3 inch lift kit will provide 3 inches of lift in the rear.

A: The Revtek 3 inch lift utilizes OEM shocks/struts