Installed on a 79 K10 with 33in tires. Fit like a glove to stock mounts with pro comp bolts. Today I got to 65 for the 1st time without feeling like a rattle trap lure.
A friend recommended Pro Comp and after the easy install & test drive...I'm a fan as well.
By It's a truck from Taylor TX
Direct bolt in replacement
Great bolt in replacement and works perfectly. Way better than those others that you have to modify to install. This is the right way to go.
By hotrodguy from Woodland Hills CA.
Broke within weeks
This stabilizer was recommended as a replacement for oem 2012 Powerwagon steering stabilizer. The truck has 10k miles and no problems other than needing a new stabilizer after I bent OEM stabilizer while off roading. I got the first death wobble after about a month I put it on. After hearing some recommendations and negative oppinions about this one I decided to put on Carli's stabilizer. When I took it off I relized it leaked (I have a skid plate under it and it was covered in some sort of oily liquid) and when I tried quickly moving the piston back and forth it felt like it had a half an inch gap before it fully engaged. Carli's stabilizer looked heavier duty and better quality. It also had more dampening and would actually push the piston back. Don't be cheap and get a quality shock/stabilizer so you don't have to go through the same thing. It's been about a month and 1k miles - no death wobble. By the way, 4wheel parts store was great and although they didn't have to they listened to me and gave me my money back in store credit.
By mrD from UT
This unit needs to be slightly longer to bolt in place of the stock unit. If not, the main body which is fat will rub against the track bracket. 4 wheel parts are good about replacing it but plan on doing that often. If you adjust the bracket on the other end you can make it fit better but the shock then is in harms way and will suffer clearance issues. I would spend the money on a better unit that is either longer or thinner and be done with it.
By Doc from PHX
i would not buy again
leaking in less than 6 months
By rubicon crawler from turlock, ca
It will fit!
The Full-Traction unit that I replaced had a smaller diameter housing; and I was concerned that this item would be too large to fit properly and avoid interferrance with the JK track-bar or diff. cover. However, there was plenty of adjustability at the tie-rod clamp to maintain clearances. Product works as well as the item replaced.
By Yelo-RUBI from Santa Clarita, CA
love all your stuff
By lenninger8 from cedar crest NM
had leaks with brand before
By june from sicklerville nj
A great replacement item for the junky stock one.. Made a big difference and am glad I got this one!
By TCB from Eustis, Fla
98 jeep wrangler Steering Stabilizer
off roading , daily driver
By All 4 on the Floor from south gate ca
The EXP220230 will fit your Samurai but it will require a mounting kit part # EXP2508.
This mounting kit has a bracket that clamps around the axle on 1 side and the has a bracket that clamps onto the tie rod. It is a very simple bolt on installation. If you already
have the brackets on the Samurai and you just need to replace the cylinder the EXP220230 should work fine. It has a stem type mounting on both ends. Thank You
for your question.
from Tamaulipas, MX on
Is there a boot to go with this damper?
jim from on
Any of the Pro Comp Poly-Vinyl Shock Boots will fit. Please type "Shock Boot" in the large search bar at the top of the product page. This will result with every color we offer. Thank you.
will this es2000 steering stabilizer shock fit my f250 4x4 from stop to stop.
BOB from SAN BERNARDINO on
Yes, the Pro Comp Suspension Single Steering Stabilizer Kit will fit your vehicle application.
Pro Comp Suspension has spent the last two-and-a-half decades engineering, testing and manufacturing products that will give Jeep drivers the confidence to dominate whatever terrain is ahead. The Pro Comp Promise Life Time Warranty is forever. Pro Comp's warranty goes with the suspension products on Jeeps whether or not the Jeep owner is the person who originally purchased the product. Pro Comp Suspension can afford to give such a warranty because the products are produced at the Pro Comp facility in San Diego, California under exacting manufacturing standards. Pro Comp Suspension is the only suspension company with products that are tested under true driving conditions on outside roads, rather than simulated testing. Shop Pro Comp Suspension Now