Pro Comp Coil Springs

A: Hey Raudy, Apologies bud but these coils are designed for 3-4.5" of lift, while the Skyjacker kit only accommodates up to 3" of lift. Please feel free to swing by one of our stores: https://www.4wheelparts.com/stores/find-a-store Or reach out to one of our vehicle experts at Toll Free: 1-877-474-4821 Thanks for reaching out!

A: No it does not.

A: OD: 5.124” Spring Rate: 120 +/- 5% lbs/IN Free Length: 21.718”

A: Components to complete 2.5” lift are in separate box 55701B.

A: The EXP 55201 is 2.5” front coil for the JL/ JT models. It will work with 4WD and 2WD applications.

A: Free Length (Inches) 18.88 Spring Rate (Lbs/ Inches) 207 Spring I.D. (Inches) 4.94 Wire Diameter (Inches) 0.656 Weight (Lbs) 14.25 Spring Location: Rear

A: Do you have a body lift or do you have spacers on top of the factory shocks? We need a little more info about your setup to get you the correct parts. Please call our sales line toll free at 1-877-474-4821

A: No - these fit the new Wrangler JL models.

A: If those shocks have enough travel for 3-4.5" lift, these should fit.

A: Hi Bubbs, Using the Pro Comp 3 Inch Lift Coil Springs will not work for your application to remove the leveling spacers. Tacomas have a coilover front strut, so in order to remove the spacer and still have the same ride height you would also have to get longer struts to mount the coils onto. Currently your coil spacer is bolted on the top of the front coilover assembly, between the top plate of the coilover and the frame of the truck. If you only got springs, they most likely would not be able to fit into the strut assembly. If you contact our customer service center @ 877-474-4821 they can go over all the options

A: Hello Enrique, Sorry, you can not install this set of coil springs with the 2.25" level kit. running both together will create drastic steering and driveline angles. Thank you.

A: Hello Jake, the Pro Comp Suspension 3 Inch Lift Front Coil Springs part# EXP57491 will work with your prorunner shocks and struts. You will still be able to adjust the front struts. Thank you for your inquiry.

A: Hello Ivan, The Pro Comp Suspension 4 Inch Lift Rear Coil Springs part# EXP55498 is a stiffer spring than your factory springs. Thank you for your question.

A: Hello Robby and thank you for your question! Pro Comp Suspension 3 Inch Lift Front Coil Springs part number EXP57491 are springs for a 2006-2008 FJ Cruiser.

A: Hello BR and thank you for your question! Pro Comp Suspension 3 Inch Lift Front Coil Springs will take the place of your front spacers and the shocks you have now with the 3" lift should still be long enough for the Pro Comp 3" springs.

A: Hello Rocky, the mx coilover springs can be purchased at the store special order. Thank you for your inquiry.

A: Hello Rocky, the Pro Comp Suspension 3 Inch Lift Front Coil Springs are designed for the pro comp struts or the factory struts. These will not work with the mx coilovers. Thank you for your question.

A: Hello Scot, Thank you for asking. The Pro Comp Suspension 3 Inch Lift Front Coil Springs do require you to have a longer front struts to accommodate the lift coils. You will need quantity two of these http://jo.my/l9yvkh.

A: Hi Jon, Thank you for asking. The Pro Comp Suspension 3 Inch Lift Front Coil Springs do not come with the trim spacer. Old Man Emu is the only trim spacers that i know of, part# OME95PF5. It is not on our website but we do sell them. We have not had any issues with these coil springs being rated at 719lbs

A: Yes the Pro Comp Suspension 3 Inch Lift Front Coil Springs will work on your truck but will require other parts if you are planning on lifting the vehicle.

A: Hello Austin, The Pro Comp Suspension 3 Inch Lift Front Coil Springs do require a aftermarket strut to allow for additional travel.

A: Banksy, These coils come out of the 3" pro comp complete kit. They are made to be used with the pro comp es6000 shocks that come with the kit. I wouldn't recommended installing them on the factory struts.

A: Hello Pistolpete, the Pro Comp Suspension 3 Inch Lift Front Coil Springs will not fit your vehicle. Thank you for your question.

A: Hello Ross, the Pro Comp Suspension 3 Inch Lift Front Coil Springs part# EXP57491 is not recommended to stack on top of your existing lift. This will cause issues with alignment as well as ball joint and cv axle issues. If you are looking to lift your vehicle higher you may want to consider a body lift. Thank you for your inquiry.

A: Hello Al, the Pro Comp Suspension 3 Inch Lift Front Coil Springs part# EXP57491 will fit your vehicle however you would need to remove your front spacers and make sure your struts are at the stock setting. If you try and stack this with your current setup it will not work. Thank you for your inquiry.

A: Scott- Thanks for your question. The Bastien 5100 RHA shock that would fit your application is part number BIL24-186711. I cant say they will give you a smoother ride than the stock shocks you are using now.

A: Chris- Thank you for your question. If you use Pro Comp Suspension 3 Inch Lift Front Coil Springs and the Bilstien 5100 you will have to leave the shocks on the stock setting. The Coil springs are a higher spring rate and stiffer than stock springs.

A: Hello Danny, The Pro Comp Suspension 3 Inch Lift Front Coil Springs EXP57491 fit the 2006 - 2008 Toyota FJ Cruiser 4WD. Thank you for the email.

A: Hello Austin Offroad, The Pro Comp Suspension 3 Inch Lift Front Coil Springs EXP57491 are a 718lbs/inch or 12kg in metric spring rate. It would depend on the spring rate you are running now. If this vehicle if 4wd you will need to keep and eye on the front axle CV's. Please make sure the boot fits are not touching one another.

A: Dom the Pro Comp EXP57491 measures free standing 15.74" tall with an I.D. of 2.875" with an O.D. of 4.244" the spring rate is 718 Pounds per inch with a wire diameter of .781. hope this helps thank you

A: Trieu- Thanks for asking. The spring rate for the Pro Comp 3 inch front lift front coil springs is 718lbs/inch or 12kg in metric.

A: Ben, The Pro Comp Suspension 2.5 Inch Lift Rear Coil Springs EXP55593 will require an adjustable rear track bar.

A: Ramiro, Please see my email. We need to clarify a few more details with your vehicle.

A: The Pro Comp 3 inch lift springs are not compatible with your stock shocks.

A: 760, Sorry, you can not add the Pro Comp Suspension 3 Inch Lift Front Coil Springs EXP57491 to your Adjustable Bilstein 5100 Coilovers. The spacers takes up the space above the shock cap and the chassis mounting location. The issue you will run into is the coilover not being long enough to accommodate a taller spring. Check you extended and collapsed coilover lengths.

A: Jimbo, Yes, the Pro Comp Suspension Coil Spring EXP57491 are compatible with the front ES6000 Struts