A: They come with the center caps but not the lug nuts.

A: No lug nuts

A: Comes with center caps.  You need to order lugnuts.  Order a set on Amazon with nuts and locks.  Cheaper. I don’t know if they will fit your truck but the website has a chart on which tell which models they will fit.  

A: The Center Caps are included however the lug nuts are sold separately. Use the Pro Comp 32-Piece 14x1.5 Lug Nut Kit (Chrome) - Part number PXA16145

A: No the center caps are closed but you can mount the rim without the center cap for your locking and unlocking of hubs 

A: The center caps on mine it looks like you can pop the cap off and they would then be open center caps. You can also not use the center caps at all if desired.

A: Please contact Pro Comp customer service at 800-776-0767

A: I think that year Chevy was a 6 lug.  These are the 8 lug wheel.  There is a guide on their website (4wheel parts) which will guide you to purchasing the correct wheels.  Be sure.  69 c10. Very nice.  

A: Check the lug pattern. Yours will be most likely be the the 6x 5.5. Otherwise these rims are excellent

A: I put the center caps behind the wheel spacers.

A: Please call our sales line toll free at 1-877-474-4821

A: PXA1069-6882 has an offset of 0. Apologies we will have that fixed asap. Thanks for reaching out!

A: They come with hub caps but not lug nuts.

A: I put them on my 98 Ram 2500 so yes

A: Offset refers to the wheel’s mounting surface relative to the centerline of the wheel. So, zero offset places half the wheel on each side of the mounting surface. Positive offset results in a narrower track width, with the mounting surface closer to the outside of the wheel. The opposite is true for negative offset wheels. The size of the hole in the center of a wheel is known as the center bore. It is measured in millimeters. Some factory wheels have a center bore that matches exactly with the hub to reduce vibration by keeping the wheel centered. Noah give us a call 877-474-4821

A: They fit my 92 F250. Sterling 10.25 full floating rear axle, dana 50 TTB front.

A: They fit my 1992 F250 with 6 inch suspension lift. I have two sets, 16x8s are on it now with Q78-16 TSLs, 16x10s have 37 inch BFG all terrains...

A: Thread size (Lug Nut Size): M14 x 1.5 (Pro Comp 32-Piece 14x1.5 Lug Nut Kit (Chrome) - PXA16145)

A: The Pro Comp 69 Series Vintage Wheel, 16x8 with 8 on 6.5 Bolt Pattern - Polished - 1069-6882 has the same bolt pattern (8x165.1 (8x6.5)) as the 1967 Ford F-250.

A: The 2009 Chevy Express van 2500 uses the 8 on 6.5 bolt pattern, and use lug nut thread size: M14 x 1.5

A: No, you will need an 8x170 bolt pattern. 1069-6870 https://www.4wheelparts.com/p/pro-comp-69-series-vintage-16x8-wheel-with-8-on-170-bolt-pattern-polished-1069-6870/_/R-BKBQ-1069-6870 16x8 -12mm face of the wheel is not that far in. The image on our site is 10” wide wheel

A: The bolt pattern and size look to be correct for your truck. I would just verify the center bore to make sure they would clear: Center Bore Diameter is 5.150 in. or 130.81mm

A: PXA16144 – chrome PXA16144B - Black

A: Please call our support team to verify if this will fit your setup. Toll Free: 1-877-474-4821

A: Yes

A: This is the correct bolt pattern for your F-250. I'm not sure what size tires you plan to run and clearance with the hubs. Please call our tech line for further assistance Toll Free: 1-877-474-4821

A: Hello Rick and thank you for your question! Pro Comp Alloy Wheels Series 1069, 16x8 with 8 on 6.5 Bolt Pattern - Polished come with a 2 piece center cap that slides in from the back side of the wheel and the end of the center caps pops off.

A: Hello Rick, Yes, the center bore of this wheel will fit over a manual locking hubs on your vehicle application. Thank you for the question.

A: Hello shawn, Yes, this wheel is clear coated. Thank you for the question.

A: Hello Trumpet Geek, Yes, the Pro Comp Alloy Wheels Series 1069, 16x8 with 8 on 6.5 Bolt Pattern - Polished will fit your vehicle. Thank you.

A: Hola Apohisf, Los Pro Comp Alloy Wheels Series 1069, 16x8 with 8 on 6.5 Bolt Pattern - Polished no caben.

A: Hello Bill, The Pro Comp Alloy Wheels Series 1069, 16x8 with 8 on 6.5 Bolt Pattern - Polished will fit most 2003 Chevy Silverado HD models.

A: Hello Nate, the Pro Comp Alloy Wheels Series 1069, 16x8 with 8 on 6.5 Bolt Pattern - Polished part# PXA1069-6882 has a hub bore of 130.81mm. The center caps come with these wheels so you do not need to purchase them separate. If you have lost one, the part number is on the inside of your other caps. Thank you for your inquiry.

A: Gary- Thanks for the question. The X wrench is a heavy duty professional grade tool box quality heat treated chrome vanadium alloy steel foldable 4-way lug wrench. Has a patented heavy duty quick release button for quick fold capability for easy store & save space. 4 common sockets to fit most lug nuts, 11/16, 3/4, 13/16 & 7/8. You can find one here PXAXWRENCH Tire deflators are used to air down your tires for off road traction. They attach to your valve stems and are adjustable to air down in increments of 3 PSI. all the way down to 8PSI. You can find them here http://jo.my/p9ge0m