Power Trax Dana 30 27 Spline Lock Right Locker - 2210-LR

universal fit logo


  • Power Trax | Part Number: PTX2210-LR
  • Popular Axle Manufacture:Dana
  • Fitment:Universal Fit
  • Axle Spline:27 Splines
  • Differential Type:Automatic Locker


Brute Force Devices For Rugged Applications, Best Value For Greatly Increased Traction, Complete Replacement Of Diff. Case Not Installation, Ring And Pinion Setup Not Altered, Installs Easily In Front/Rear Or Both, Proven In Most Demanding Applications.



Works Great!

My cherokee is purely for offroading and installing this lockright in my front end has made a world of difference. I would highly recommend.I have no problems steering on road. The instructions are little vague and the pictures of our little blotchy, but after watching a few YouTube videos from others on how to install it, it worked out just fine. I would highly recommend this locker.

from Phoenix, AZ |

This locker is easy to install if you have everything that you need to completely remove the differential from a Jeep DANA 30 frontend. You don't need to reset any gearing, shimming, etc., but you do have to take it out to install. Once in, appreciate the awesome difference.

from San Antonio, TX |
Works Great

Locker installed in about 45 minutes, install went smooth and had no hic-ups. Works great in the rocks and in the mud. I can now walk up trails that I struggled on before. Locker can take a fair amount of abuse, its holding up to 35" KM2s right now with no problem.

from Port Neches, Texas |
Works Great

Installed in 2010 Wrangler. Very easy to install. Excellent directions. Works great. Makes very little noise.

from Charlotte NC |
Great Dana 30 Locker!

This is a great locker for a CJ Dana 30!

from El Paso Texas |
Easy to install works great.

Install was easy but instruction book pictures were blury and hard to see. Works great in my 1992 Jeep YJ front Dana 30. Can't tell it's there in 2wd but in 4wd it's a big differance.

from Radford VA |
A great product

made a world of difference

from apache junction az |

Question & Answers

29 Answered questions

Hello, I have this product along wth the Powertrax no slip in the rear. I'm currently running 3:73 gears but wish to go to 4:88's. Will my lockers still work with the new gearing? Lastly, FYI to all ,these are great products which can't be beat for the cost. Thank you John 2003 Jeep tj with D30 front and D44 rear 3:73 gears ,35's, 4" lift with SYE and cv

Asked by Patriot from Firestone CO on

Hello Patriot You can run your LOCK RIGHT and your stock open diff case in the front. you will need G/2-2031-488 front ring and pinion kit, G/235-2031 master bearing installation kit and 2 each D/S46470 inner axle seals. In the rear you can keep your Powertrax No Slip and your stock open diff carrier. You will need a G/22-2045-488 ring and pinion kit and a G/235-2045 master bearing install kit. If you have any questions or want a quote then please give me a call. Thank You for your question. Jon Snyder 4Wheelparts Gear Squad 877-757-8444 ext 1844

Answered by from Firestone CO on

I have a 2013 JKU with a Dana 30 front end. will this work on my vehicle? thanks for your time

Asked by jeepinjim from Big Bear Lake, CA on

Hello At this time we don't have a unit to fit the JK Dana 30. They changed the spider gear size on the 07 and newer Jeeps. Thanks

Answered by Rody from Big Bear Lake, CA on

97 jeep wrangler 2.5 tags on rears read as follows: front 52099439 10 610630 3 rear 52067994 4 11 5747 will this product fit both the front and rear rears? thank you, I noticed the catalog i have shows a different one for the rear

Asked by Douglas from pa on

Hello Douglas The rear axle is the Dana 35 front is the Dana 30 The front part number is PTX 2210-LR and the rear is PTX 2311-LR Thanks

Answered by Rody from pa on

See all questions & answers