Garvin Industries Roof Racks

A: Sorry, thought this item was #20000. Yes, the #55000 fit the FJ cruiser. 

A: This will fit the FJ. 

A: Good quality. Be able to carry over 70lb cooler. You get what you pay for. But only fit Jeep Wrangler JL. 

A: It would be pretty difficult. If you were set on trying, your best bet would be to attach it to the factory rails, not the rack, and the rack would actually get in the way at that point

A: The ARB awning mount #38005 will work just fine on the Xterra factory rails with Garvin's basket rack #38010 installed.

A: Only the front Freedom panels. The rack needs to be removed for the removal of the rear section of the hardtop.

A: You would not be able to take off the whole top as the rack has a mount on side rear window panel.

A: The rack itself wraps underneath the Jeep and has two anchor points. The main support is accessed from inside the tail light area. You have to remove the tail light and install your first bolt there. Then there is a piece that attaches to the body/frame under the Jeep with 3 hex bolts. Hope this helps explain it. I've had my rack on for years and have carried everything from canoes to roof top tents with no issues.

A: I didn't see a attachment listed from Gavin Industries for a canoe. You might look into the Rhino-Rack Vortex SG Black 2 Bar Roof Rack - SG60 | If you’re traveling with a canoe, we recommend the #RLH1 or #RLH2 Adjustable Canoe Holders. These effective carriers will lock your canoe in place, so it doesn’t slide around during transit. Load the canoe from the rear by sliding it up and into place between the Adjustable Canoe Holders. #RLH1 and #RLH2 can be fit for both Vortex and Heavy Duty bar types.

A: It hasn't been tested to fit. To be safe I would say no.

A: You have to tilt the rack back by removing 6 bolts to raise or lower the soft top.

A: The top of the rack is 39” above the top of the rear taillight.

A: It is the only picture Garvin has of this rack. This particular part number is for the 2-door models. For the 4-door rack, use this part number: https://www.4wheelparts.com/p/garvin-expedition-full-rack-20074/_/R-GARVI-20074

A: Yes it will. We are updating fitment on this part.

A: No we do not. You would have to call Garvin and get it from them.

A: It will only work on the 2nd generation Xterra. They don’t offer one for the 1st generation.

A: It wont be a direct fit, you would have to do some modification as this latter is meant for a Adventure rack, Feel free to call into the sales line to place an order. If you live near a store you can set it up for in store pick up. Sales & Support Toll Free: 1-877-474-4821 Phone Sales (PT) Monday - Friday: 5 a.m. - 7 p.m. Saturday: 7 a.m. - 3 p.m. Sunday: 8 a.m. - 2 p.m.

A: Yes you can. You will need to purchase our crossbar kit #44085 to attach the tent to the Adventure rack.

A: The rack attaches directly to the hardtop so you can’t remove the hardtop without removing the rack as well.

A: You would need to tilt the rack back to raise or lower the soft top. It requires removing 6 bolts to tilt the rack back.

A: Yes, this will fit your 2017 JKU. We will fix the fitment issue for this part.

A: Yes they should they're same diameter 2.25 like the xterra

A: The rack is designed to tilt all the way back and rest on the ground. The only issue would be an aftermarket bumper that would prevent it from tilting it all the way back.

A: They are designed to work with 1” round. 2” will not work.

A: Hello, So in order to install the rack, you will need to remove bumper for install, but once the brackets are in place you can put the bumper back. If you plan on installing yourself, before tightening everything down completely make sure you open/close all the doors, to check clearance and to ensure nothing rubs/hits/touches. Good luck and thank you for your business.

A: Hello Bill, This part number only fits the 2007 to 2016 Jeep JK Wrangler 4 Door Models. GRV44092 is the part number for the 2 door models. Thank you.

A: Hello Mike, All roof racks are rated for 300 lb of evenly displaced load. You can simply remove the rack when not in use. Thank you for the question.

A: Hello Kel, Yes, you can carry two kayaks provided both are less than 4" wide. This works with all 4"H Garvin/Wilderness Racks. Each kit contains 4 brackets to attach two Yakima/Thule crossbars. Thank you.

A: Hello Brandon, Yes, you can install a roof top tent on this unit. Since RTT's are displaced weight you will not have an issue. The 300lb limited is more for a focused weight limit. Thank you

A: Thanks for the question. This should fit on either side of the rack. Thank you.

A: You can place it on the phone with me if you would like 310-900-5558 Morgan and I will send it to the store.

A: Hello Big E and thank you for the inquiry on the Garvin Industries Yakima/Thule Crossbar Adapters. The parts list for this item is as follows: (4) 4" mounting brackets (4) inside mounting brackets (4) lower brackets locknuts, bolts, and washers. Here is the link to get you back to the ordering page: http://jo.my/19f4vz.qrcode

A: Hello Rob and thank you for your question! Garvin Industries Overhead Expedition Rack for JK Wrangler should work with the Atlas Bumper here is the install instructions http://www.4wheelparts.com/aux_incl/pdf.ashx?pdf=44074.pdf&line=GRV.

A: Hello Zooks Yes we do here is the part number so you check it out on the website. type this part number in the search field GRV 4450

A: Hello Roberto, the Garvin Industries Overhead Expedition Rack for JK Wrangler Unlimited part# GRV44074 weighs in at 141 lbs and the dimensions are 54"x93.5"x4". Thank you for your question.

A: Robert- Thanks for asking. If your windshield lights mount to the outer screws on the windshield hinge then yes the Garvin Industries Expedition Rack for TJ Wrangler will interfere with them.

A: Thanks for the inquiry mazakas, the Garvin Industries Track Rack for JK Wrangler Unlimited part # grv44014 can use a part # GRV29956 for your 48 inch rack.

A: Hello Tim, the Garvin Industries Trail Rack part# GRV44000 will clear your bumper combo. With your bumper combo you can clear up to a 35" tire. Thank you for your inquiry.

A: Walt, thank you for your question. Garvin Industries Expedition Rack for TJ Wrangler part# GRV34098 fits Jeep 97-06 TJ Wrangler so it will fit your vehicle.

A: Jeff- Thanks for the question. I have not hear of any reports with the Garvin Industries Overhead Expedition Rack for JK Wrangler Unlimited causing GPS issues.

A: R. Johnson- Thanks for the question. The Garvin Industries Trail Rack bolts on to the tailgate without drilling. You do not need to remove the third brake light but you will need to remove the spare to gain access to the bolts.

A: Jon- Thanks for asking. The Garvin Track Rack for JK Wrangler Unlimited does not come with a weight rating. This is because the rack will support more weight than the hard top can handle. Garvin recommends following the weight rating of your hard top.