Fab Fours Black Steel Front Ranch Bumpers

A: The bare steel bumper is no longer available.

A: PRODUCT DETAILS: 2″ Bolt on Receiver | Mounts to the top of Black Steel bumper series | Works on 3/4 and 1 ton applications ONLY. Part Number: FFIM1750-1 or PRODUCT DETAILS: 2″ Bolt on Receiver | Mounts to the top of the ELITE bumper series | Works on 3/4 and 1 ton applications ONLY. Part Number: FFIQREC-1

A: This bumper is already sensor compatible.

A: 2007-2013 GMC 1500 BLACK STEEL FRONT BUMPER (PRE-RUNNER GUARD)

A: Works with factory fog lights on 94-2018 models only. All 2019-2021 will accommodate a 3″x 3″ LED cube.

A: Accommodates factory front camera (2019-2021). Minor Camera Interference with Pre-runner Guard and Full Grille Guard. Replacement Front Sensor Lower Guard Vertical Plate (2019-2021 models only): (Q21983-1) Sensor Compatible. Only 2019-2021 Models are Sensor Compatible

A: The Optional- Ranch 2″ Receiver (Part No. M1750-1) is drilled and bolted to the frame rails. Works on 3/4 and 1 ton applications ONLY. No weight rating is offered.

A: The sensors will work fine - Optional bolt-on winch mount (Accepts up to 16,500 lb. winches or smaller)

A: 14 Gauge US Steel

A: I do not have an image of the full guard of the Elite bumpers but the Black Steel is the same minus the mesh that is between the bars. Hopefully you can visualize this image without mesh. You can see fine but obviously there will be some cross bars in front.

A: 300#

A: Yes it will fit.

A: You need part number FS08-T1350-1: https://www.4wheelparts.com/p/fab-fours-rear-ranch-bumper-black-fs08-t1350-1/_/R-DKSN-FS08-T1350-1

A: Yes - it fits 94-21 Dodge Dodge 2500-5500

A: Fab Fours has never tested any plows. It will vary on how the plow mounts. But from what I’ve seen most often the plow arms are going to interfere with the lower part of the bumper. You would most likely have to make modifications to work. Unless it mounts to a 2” receiver which we do have as an option for that truck.

A: Shipping weight is 300#. Actual weight would be close to that.

A: We do not. You would need to contact Fab Fours for further assistance.

A: Yes, there are pre-drilled holes in the lower guard.

A: Yes we will. Please contact your local store for more information. https://www.4wheelparts.com/stores/find-a-store

A: One or the other. And the D ring kit is sold separately

A: For the Fab Fours front bumpers, you have the options of choosing a full guard, pre-runner guard, or no guard. The full guard option provides the maximum protection by shielding the grille and headlights from damage. The pre-runner guard would protect mostly the grille.

A: Hello Dave, We recommend the installation of the Pro Comp Suspension Nitro 2.5 Inch Lift Kit Part Number: EXP61180K when installing this bumper. That will help with the additional weight. Thank you for the question.

A: Hello Jake, Yes, you will have to remove that part to install this bumper. Thank you.

A: Hello Cody, Shipping weight is 275 pounds. Thank you for the question.

A: Hello outdoorsman80, Yes, this bumper can be installed on a vehicle with a body lift. Thank you for the question.

A: Sir, Pre-Runner is referring to the style which is the tube style bumper. and will accommodate a winch. This is a very stout bumper for your stock 2015 f250. Thanks for your question.

A: Thanks for the inquiry Bob, the Fab Fours Front Ranch Bumper in Tread Plate with Tow Hooks part # FFIDR10-S2962-B this is not in stock and will have to be ordered.

A: Thanks for the inquiry Marj, the Fab Fours Grille Guard Front Ranch Bumper in Bare Steel Tread Plate part # FFINT04-K1760-B is not in stock and would take about 3 weeks to get.

A: Hello Tyler, the Fab Fours Black Steel Front Ranch Bumper with Pre-Runner Guard in Bare Steel part# FFIGM14-S3162-B will work with your factory sensors if you drill out the holes. Thank you for your inquiry.

A: Hello Dr G, the Fab Fours Full Grille Guard Front Ranch Bumper with Tow Hooks in Black powder Coat part# FFIFS11-S2560-1 weighs in at 300 lbs. Thank you for your inquiry.

A: Hello Perro, Please email me direct at schism@4wheelparts.com with the bumper part # and a complete ship to address and I can get you a total delivered price to your country.

A: 250LBS 92X47X36 this has to ship by truck freight on a pallet. We can ship it directly to you or to a freight forwarder. Thanks

A: Hello perro and thank you for your question! Fab Fours Front Ranch Bumper with Tow Hooks in Black Bare Steel Tread Plate does come with all hardware you need to install the bumper on your truck.

A: Hello Horton, the Fab Fours Front Ranch Bumper with Tow Hooks in Black Powder Coat Tread Plate part# FFIFF09-K1961-1 will require you to remove the current grille guard that you have. Thank you for your question.

A: Hello Crispy Cummins and thank you for the inquiry on the Fab Fours Front Ranch Bumper in Bare Steel Tread Plate with Tow Hooks. This bumper weighs 300LBS. Here is the link to get you back to the ordering link: http://jo.my/qc6phi.qrcode

A: Hello Bill and thank you for the inquiry on the Fab Fours Full Grille Guard Front Ranch Bumper with Tow Hooks in Bare Steel. I can honestly tell you that the airbag will always go off if you hit something hard with the front end of your vehicle. There is no way for you to "turn off" your airbag system from doing it's job that it was intended to do.

A: The Fab Fours Pre-Runner Ranch Bumper with Tow Hooks in Black Powder Coat Tread Plate comes with all hardware needed to install. Nothing else is needed. Hope this helps!

A: Hello Kd3, the Fab Fours Pre-Runner Ranch Bumper with Tow Hooks in Black Powder Coat Tread Plate part# FFICS07-K2062-1 is available in bare steel so that you can paint it however you would like. Thank you for your inquiry.

A: Thanks for the inquiry KD3, the Fab Fours Pre-Runner Ranch Bumper with Tow Hooks in Black Powder Coat Tread Plate part # FFICS07-K2062-1 is the diamond plate finish.

A: Thanks for the inquiry KD3, the Fab Fours Pre-Runner Ranch Bumper with Tow Hooks in Black Powder Coat Tread Plate part # FFICS07-K2062-1 comes black if the part # ends in -b part # FFICS07-K2062-B, B stands for bare steel.

A: Hello Justin, Thank you for the question. Yes, this bumper will clear a 35x12.50R17. Just make sure you have the correct wheel backspace.

A: Justin- Thank you for your question. The Fab Fours Pre-Runner Front Ranch Bumper with Tow Hooks in Black Powder Coat will fit with your fender flares with out modification.

A: Wild Bill- Thank you for your question. The Fab Fours Front Ranch Bumper in Black Powder Coat Tread Plate with Tow Hooks is a fully assembled one piece design. You will need to remove the whole factory bumper including side trim pieces to install it.

A: Hello Randy, Thank you for the question. The Fab Fours Pre-Runner Front Ranch Bumper in Bare Steel Tread Plate with Tow Hooks FFIGM08-S2162-B is a 100% bolt on application. Complete installation instructions comes with the bumper.

A: Hi Chadwick We dpo not have that image on file i would recommend contacting the manufacture or doing a Google search Thank You

A: Hello Loganberry, Thank you for the question. The Fab Fours Grill Guard Front Ranch Bumper in Black Powder Coat Tread Plate with Tow Hooks FFIDR03-S1060-1 remove the factory tow hooks. However, they do include an aftermarket tow hook kit with this bumper. Here is a direct link to the installation instructions http://jo.my/v7tigg

A: Hello Donny, Thank you for the question. The correct part number to that bumper is FFICS07-K2061-1 Here is a direct link to that bumper http://jo.my/ybwnef

A: Jake- Thanks for asking. I checked with Fab Fours and they say this Grill Guard Front Ranch Bumper in Bare Steel Tread Plate with Tow Hooks will fit your 2001 Dodge Ram 3500

A: David- Thanks for asking. The easiest way to tell if you have a classic or regular 2007 GMC Sierra 2500HD is to look at the headlights. If your headlights are two pieces per side then it is a classic, if the headlights are one piece per side you do not have a classic.

A: Thank you for your question. The Fab Fours Grill Guard Front Ranch Bumper in Bare Steel Tread Plate with Tow Hooks part number FFIDR94-S1560-B weighs in at 300 pounds

A: Hello Will, Yes, the factory fog lights will fit this bumper. Thank you for the email.

A: Von- Thanks for the question. The lights pictured on the Fab Fours Full Grille Guard Front Ranch Bumper with Tow Hooks in Black powder Coat are the factory Dodge Fog lamps. We do mot carry them at this time.

A: Austin- Thanks for the question. I show the Fab Fours Pre-Runner Front Ranch Bumper in Black Powder Coat Tread Plate weighs 250 lbs.

A: Thank you for your question. Yes you can add a 2" receiver on Fab Fours Pre-Runner Front Ranch Bumper with Tow Hooks in Black Powder Coat part number FFIDR09-K2462-1. Fab Fours offers 2 bolt-on application that are universal to all Black Steel bumpers, here are the link to those products - part number FFIM1750-1 http://jo.my/oxf3yn and part number FFIQREC http://jo.my/wuupiu

A: Thank you for your question Charlie. I just got off the phone with Fab Fours and they said "the bumper sticks out 8 to 12 inches past the truck" for the Fab Fours Full Grille Guard Front Ranch Bumper with Tow Hooks in Bare Steel part number FFIFF09-K1960-B

A: B.Hemi- Thanks for the question. The Fab Fours Pre-Runner Front Ranch Bumper with Tow Hooks in Black Powder Coat is a direct bolt on. These bumpers ship directly from the manufacturer so depending on their inventory there me be a slight delay.

A: Dusty- Thanks for the question. You can find the Fab fours winch plate here http://jo.my/gvv8ul

A: Paul- Thanks for asking. The Fab Fours Pre-Runner Front Ranch Bumper with Tow Hooks in Black Powder Coat does have an option winch plate but unfortunately it will not work with 1500 series trucks.

A: Rusty- Thanks for the question. There is no winch mount available for the Fab Fours Front Ranch Bumper in Black Powder Coat Tread Plate with Tow Hooks when installed on 1500 series Silverados. This bumper is available without a grill guard here http://jo.my/ci3dda