due to injury, had to have mech shop do the install. It took them 2 days to install the kit.seems it shouldnt take that long,but it did.
By DesertRunner from Cheyenne,Wy.
easy to install...a perfect fit
way better than stock...the quality is obvious...I knoww it will save me money in the long run...wish I would have got these when the stock bearing assembly went out the first time...Better readable copies of the schematic would help but all in all not a bad install
By redox from emerald isle nc
Yes, it works, saves tires and gas
I installed this kit on my 2004 Dodge Ram 2500 long bed, four door, 4WD, Hemi, auto truck. Took the old Dodge junk out of the front and put this kit in. Completely different truck, stopped eating and cupping the front tires, turns nice, no hopping, and rides quieter. Ran it now for about 6500 miles, 1200 mile highway trip and the rest local driving. Saw an increase in mileage from 10.0 average and 10.3 high sometimes, 12.8 highway, before the kit, to a 11.3 average, and 14.3 highway, so it is alot better. I am running Firestone MT lugs too, so it still helped. Truck weighs about 7900lbs, with tanks, and hitches.
I know it is a Dodge, but it handles like my old F250 trucks, easy to install. Only thing I did not like, is the new studs are too long to put the hubcaps back on the front and lock under the lugnuts, so I doubled the lug nuts on 4 of them, and the hub cap sticks out a bit, but looks good. Solution is to put in the shorter studs if you have them on it from new.
As far as customer service, very helpful, no issues, great tech support, as my wheel bearing on the old set went out two days before the kit came in. They expressed it to the house, no issues.
By skip from Pennsylvania
I would buy this product again.
Much better than original parts!
By Dozer guy from Exeter, On, Canada
This is the way Dodge should've sold the truck.
Replaced two bearings on my '06 2500 Megacab diesel. When the third OEM "Unit" bearing needed replaced @ 215,000 miles, I looked at other options and found this kit. I have ran five tanks of fuel since the Freespin Hub Kit was installed and have picked-up 1.5 to 2 mpg depending on how I ran the truck.
And the fact that the bearing are serviceable as well as economically replaceable makes this a no-brainer. Struggled with doing this to a truck with as many miles as I have but I will keep the truck and this just plain makes sense.
By Craig from Fort Wayne, IN
Improved my gas mileage
By 03 ram ctd from Yelm wa
installed on 04 ram 3500 with 35000km.
old hubs and u-joints were dried out at 35000km so replace joints with greasable ones.I used precision by federal mogul #464.kit is very well machined [...]
By vince from calgary,canada
Truck drives better then brand new now, awesome!
By Hellspawn from TX
I would buy this kit again
This kit eliminates the bogus Ford superduty hubs and makes the wheel bearings replaceable and stronger too. Kit needs to be installed by someone with some knowhow as it's not for a rank amature. The kit is made tough and pretty much unbreakable
By Boxcab mike from New jersey
Expensive but worth it
This product is amazing...I can not really say go out and change your hubs today, but if you suspect anything wrong with the factory hubs these are the replacements. I now have the same performance that a friend has in his 2 wheel drive. I also have the piece of mind knowing that my universals are new and if my wheel bearing goes out it won't cost me near as much...Also Dynatrac is awsome when it comes to customer service.
2002 Dodge Ram 2500, 5.9 l magnum V8,4x4 do you supply the spicer u-joints for the Dana 60 kit?
Roy from Boise Id on
Yes we have them in stock part number D/S SPL55-3x you will need to order two.
Rody from Boise Id on
hi , i have a 2008 megacab 2500 cummins. you have it listed as it only fits up yo 2007 , so i take it there is another product number to fit the 2008 dodge?. if so what wouldthat number be. thanks again also is dyna trac giving any promotions . what is the warranty on this or can i get a extended warranty through 4 wheel parts thanks
trucker from usa on
This is the correct kit for your 2008 Dodge 2500 2000 - 2008
Here is a link to their warranty and yes 4 wheel does offer the extreme warranty on this part.
Rody from usa on
Hi iam in aust and have a 2003 dodge ram 1500 5.7 it has 5 wheel studs will this unit fit my ram thank you terry wendt
terry from south australia trott park on
This kit is for the straight axle trucks with the Dana 60 axle found in the 2500/3500. They don't offer a kit for the 1500's
Rody from south australia trott park on
Known for its brawny axle assemblies, Dynatrac got its start in the early 1990s when founder Jim McGean was building axles in his garage for off-road enthusiast friends. When others resorted to low quality parts from overseas, he took a stand and maintained production here in the states. Dynatrac's innovations include the high-clearance ProRock 60, Free-Spin hub conversion kits and heavy-duty DynaLoc locking hubs. Every axle manufactured undergoes 117 inspections during its assembly for quality assurance and the Huntington Beach, California-headquarted company has a deserving reputation as a manufacturer of high quality innovative components. Shop Dynatrac Now