Daystar Comfort Ride Leveling Kits

A: You need to measure your u-bolts to validate which kit you need: 18.4" long then you need part number KC09127 16.4" long then you need part number KC09130

A: The Dakota lift comes complete with Strut Stud Extenders and Coil Spacers. Those are the only components necessary to lift the 05-11 Dodge Dakota 2/4WD 2 inches

A: Yes, the KF09101BK will fit the 1991 3.0 L XLT Ford Ranger 2WD

A: Yes, it will lift the front 2.5”.

A: No, it will only fit the 4WD Applications.

A: No, you do not need control arm bump stops to limit down travel once 2” coil spacers are installed.

A: No, the Daystar Comfort Ride 1 Inch Front Leveling Lift Kit - KT09105BK will not fit your vehicle.

A: Hi Pentiummaker, To find out the installation cost of the Daystar Comfort Ride 2 Inch Front Leveling Lift Kit you should contact our customer service center @ 877-474-4821. They can even set up an appointment at a local 4 Wheel Parts store for you.

A: Hello Joe, Yes, this spacer kit will fit your vehicle application. Thank you for the question.

A: Hello KnowNothing, Yes, the Daystar ComfortRide 1 Inch Front Suspension Strut Spacer Kit DAYKT09117BK will fit your vehicle application. Thank you for the question.

A: Hello Charles No it does not affect the differential at all. The spacers go on top of the factory struts and is a very simple install. Thanks

A: Thanks for the inquiry ski, the Daystar ComfortRide 2 Inch Front Suspension Strut Spacer Leveling Kit part # DAYKF09129BK the total time for install is approximately 3 hours.

A: Thanks for the inquiry Ethan, the Daystar ComfortRide 1 Inch Front Suspension Strut Spacer Kit part # DAYKT09105BK normally you can stack lift struts and strut spacers, there is not enough camber/caster adjustment to align vehicle.

A: Thanks for the inquiry steve, the Daystar 3 Inch Suspension Lift Kit part # DAYKT09125BK it shouldn't but check with your local dealers service writer.

A: Hello Greg, Max tire size is a 35". Thank you.

A: Hello Danny, Technical Details: For Tire Size 32 in.

A: Hello Steve, Yes, the Daystar ComfortRide 2 Inch Front Leveling Kit DAYKC09135BK will fit your vehicle application. Thank you.

A: Hello Cold Stuff, In extreme cold situations we suggest aluminum or steel spacers. Poly also breaks down with road salt.

A: Hi Diesel The DAYKT09133BK should work fine on your 4Runner with the Cross Over Shock system. The should come up 2.5 inches which may have your front end just slightly higher than the rear end. A DAYKT09134BK is a kit that lifts the front 2.5 inches and the rear 2 inches. I hope this is helpful. Thank You Jon Snyder 4Wheelparts

A: Hello James, This kit will provide 2.5" of lift over the factory height. It will fit your vehicle application. Thank you.

A: Hi Steve We can align your XTerra at any of our stores. You will need alignment cams to be purchased and installed by us in order to align the XTerra with the front end lifted. You will need 2 each of S/P 87520 AT $36.99 each. It takes 1 alignment kit per side. Let me know if you have anymore questions Thank You Jon Snyder 4Wheelparts

A: Hello Titan, the Daystar ComfortRide 2 Inch Front Suspension Strut Spacer Kit part# DAYKN09104BK will level the front of the vehicle with the back. Thank you for your question.

A: Thanks for the inquiry MTMOPAR, the Daystar ComfortRide 2 Inch Rear Suspension System Lift Kit part # DAYKC09124 unfortunately this prdouct is not available for your vehicle.

A: Hello Jeff, the Daystar ComfortRide 1.25 Inch Rear Suspension Coil Spring Spacer Kit part# DAYKT09100BK is complete with a pair of spacers. Thank you for your question.

A: Hello Call Sign and thank you for your question! Our stores usually charge $95 per hours to install a Daystar ComfortRide 2 Inch Front Suspension Strut Spacer Leveling Kit and $125 for the alignment.

A: Hello You have to cut them because the strut bolts are taller the nut part of the stud extender. The stud extender needs to thread all the way down to the strut plate.

A: Hello Barry and thank you for your question! Daystar ComfortRide 2 Inch Front Suspension Coil Spring Spacer Kit would use the OEM alignment specs from the factory.

A: Hello Nate, The Daystar ComfortRide 2 Inch Front Leveling Kit DAYKC09125BK will not fit your vehicle application. The correct part number is DAYKC09138BK. Thank you for the question.

A: Hello Yes it will work fine with the 265/65r18 tires. If you wish next time you buy new tires you will be able to go a size larger.

A: Daystar has not done their fitment test on this kit on the 2015 as of yet. So we go by what the manufacturer says for legal reasons and insurance reasons.

A: Thanks for the inquiry Chris, the Daystar ComfortRide 2.5 Inch Front Suspension Strut Spacer Kit part # DAYKT09116BK will not fit a 5 lug, We do offer a Nitro kit from pro comp part # EXP65660K.

A: Hello master cheif and thank your question! Daystar ComfortRide 2 Inch Rear Suspension System Lift Kit will be lower then the 5" blocks you have on your Dodge.

A: Hello It depends on how out of level your truck is to make it level. If you are trying to clear a larger tire I would go two inches. You will have to look at your truck and see if that would make the front to high compared to the rear. When you measure go off of the body line not the fenderwells.

A: No this tire is about a 35x1350R18 and you would need a 6" lift to clear it. A level kit can only clear a 33" tall tire.

A: Hello Dylan and thank you for the inquiry on the Daystar 2 Inch Suspension Lift Kit. This particular Daystar kit will not fit your vehicle. It will fit a 2003 ro 2009 Toyota 4Runner. We do not sell a polyurethane kit to fit your vehicle. Sorry about that.

A: Thanks for the inquiry Alexis, the Daystar ComfortRide 2 Inch Front Leveling Kit part # DAYKC09125BK is for a 2X4, for a 4X4 you'll need [art # DAYKC09118BK.

A: Max,Thanks for the questionPart #.DAYKT09133BK will level your 2013 toyota 4Runner SR5 2WD.You can run 285/70/17 with this level kit.

A: Thanks for the question Tigerman, This is a spacer kit for the front only. It will have no affect on the air ride or the transmission. All this kit does is space the factory strut down to raise the suspension.

A: Problem child from cape canaveral, Thanks for the question. DAYKJ09108BK will fit with out any adjustments.We dont recommend a body lift on top of a suspension lift,but it can be done.

A: Thanks for the question Bob, This is a spacer for the factory strut assembly so no other parts are needed. We do recomend a fresh alignment after installation, If you are looking to replace the factory strut and level it out I would recomend the link below http://jo.my/xa79s5q qq

A: Lance, The 4x4 has a straight axle and the 2wd has control arms. The spacers are different and will not work.

A: Hello Blonde Elvis, Thank you for the question. Yes and no. You do not want to stack a spacer kit with the adjustable shocks unless you place the run the adjustable shock at stock height. If you run any spacer with adjustable shocks in a the lifted position you will have serious axle or suspension failure.

A: Hello Shootingairborne, Thank you for the question. Yes, you can use the factory 16" wheels.

A: Greg- Thanks for the question. We do not currently carry a lift kit for the express van series.

A: Hello Jody, Thank you for the question. When installing this kit we suggest the Pro Comp Suspension ES6000 Series Strut Part Number: EXP618253 for your vehicle.

A: Hello [email protected], Thank you for the question. The Daystar 2 Inch Suspension Lift Kit Part Number: DAYKT09118BK is black in color. The BK at the end of the part number states the color.

A: Joe- Thank you for your question. The Silver bolts that come with the Daystar ComfortRide 2 Inch Front Suspension Coil Spring Spacer Kit are coupler nuts. You can refer to the installation instruction for a better example.

A: Rob58- Thank you for your question. With the Daystar ComfortRide 2.5 Inch Front Suspension Strut Spacer Kit completely assembled there will not be enough room even with the ball joint disconnected to install the whole assembly.

A: Caleb- Thank you for your question. The Daystar ComfortRide 2.5 Inch Front Suspension Strut Spacer Kit will level your 2012 Dodge Ram 1500 Big horn TRX4. The issue is that the TRX4 is all ready a little taller than stock due to a preloaded spring up front. The issue come with the CV joint on the front axle shaft. It is all ready at the recommended amount of deflection.

A: Hello Allen, Thank you for the question. Yes, the Daystar ComfortRide 2.5 Inch Front Suspension Strut Spacer Kit DAYKC09113BK will fit your vehicle application. No cutting or welding is required for this bolt-on leveling kit.

A: Hi Scott These Daystar torsion bar keys simply replace the factory keys. You will require special tool to unload the torsion bars that you can rent from your local auto parts store or a two jaw puller works as well. Installation should only take you 3-4 hours. Thank You

A: Hello NMW, Yes, the Daystar ComfortRide 2.5 Inch Front Suspension Strut Spacer Kit DAYKC09113BK will fit your vehicle application. No you will not need a longer shock. This kit will be placed above your factory shock. Thank you for the email.

A: Hello Max, Yes, the Daystar ComfortRide 2.5 Inch Front Suspension Strut Spacer Kit DAYKC09113BK will maintain proper geometry. To ensure that you will need to have the vehicle re-aligned once they are installed. Thank you for the email.