Daystar Coil Spring Leveling Kits

A: No, coil spacers are not recommended with coil-over shocks.

A: Yes this will fit the 2000 C2500 Chevy Silverado w/ Coil Springs.

A: Per Daystar, this will fit if you have the new body style from 2011-April 2013.

A: This kit is for the front and rear.

A: Daystar does not recommend stacking lift kits as their coil spacers are designed specifically for factory coil springs only. Also, the vehicle may run out of alignment adjustments if you did get it to fit.

A: Hello 97XJ, This will allow you to run a 31x10.50 tire on your vehicle application. Thank you for the question.

A: Hello Joseph The DAYKG09101BK is a front lift only and will provide 2 inches of lift on your Chevy1500. I recommend 2 each of EXP915515 front shock absorbers. They are longer than stock and will provide better dampening. I would also recommend rear shock number EXP925543 for better control and dampening. However the rear shocks do not require replacement with this front only lift. The LT285/75R16 tires are very large. It would require a lot of front wheel well modification. I would recommend a LT265/75R16 tire. Thank You for your question. Jon Snyder 4Wheelparts

A: Hello jer, We suggest adding a pair of Rubicon Express Front Coil Springs Part Number: R/ERE1371 and removing the 3" coil spacers. This will give you a much nicer ride. We also suggest adding Rubicon Express Gen2 Sway Bar Disconnects Part Number: R/ERE1143. Thank you.

A: Wayne, i highly recommend new shocks as the stock ones will not let you fully extend the suspension down travel. Thanks for your question.

A: Hello No you don't need them until you get into the 2.5 to 3.0 inch lift range. Thanks

A: Eric, no the correct part for front and rear is KJ09108BK hope that helps thanks for the question.

A: Hello Jim, The Daystar ComfortRide 2 Inch Front Suspension Coil Spring Spacer Kit will fir on your 2012 Dodge Ram.

A: Hello Peyton and thank you for your question! Daystar ComfortRide 2.5 Inch Front Suspension Coil Spring Spacer Kit will need longer front shocks.

A: Thanks for the inquiry Jeff B, the Daystar ComfortRide 2.5 Inch Front Suspension Coil Spring Spacer Kit part # DAYKF09106BK we are sorry but none of our vendors offer upper control arms for your application.

A: Hello Tony, a coil spring compressor is recommended for installation on the Daystar ComfortRide 1.5 Inch Front Suspension Coil Spring Spacer Kit. Thank you for your inquiry.

A: Robby- Thanks for the question. The Daystar ComfortRide 2 Inch Rear Coil Spring Spacer Kit is 2 inches. The ride will be softer than an aluminum set of spacers due to the "give" of the material. It will still be firmer than stock because you are pre loading the suspension. The only way to retain stock feeling ride with a lift is to use a drop bracket design. This will keep the spring rates and geometry similar to stock with increased wheel well space.

A: Hello F150heritage and thank you for your question! Daystar ComfortRide 2.5 Inch Front Suspension Coil Spring Spacer Kit will require longer shocks and an alignment. Replacing the control arms will give you a better ride, but you would have to have them special made for your F-150.

A: Hello Devin, the Daystar ComfortRide 1.5 Inch Front Suspension Coil Spring Spacer Kit part# DAYKC09103BK will work on your truck. The oem shocks will be long enough for the 1.5" spacer kit. Thank you for your questions

A: Hello Big Jim and thank you for your question! Daystar ComfortRide 1.5 Inch Front Suspension Coil Spring Spacer Kit is vehicle specific.

A: Hello Tyson, Thank you for the feed back, I will let the internet team know.

A: Peyton,Thanks for the question.Part #DAYKG09101BK will work on your 1996 Chevy Silverado extended cab 2wd.

A: Thanks for the inquiry ryan, the Daystar ComfortRide 2.5 Inch Front Leveling Kit part #daykg09101bk will not fit 1988 Chevy 2x4.

A: Thanks for the inquiry ryan, the Daystar ComfortRide 2.5 Inch Front Leveling Kit part #daykg09101bk will not fit a 1988 Chevy 2x4.

A: Hello Jay and thank you for your question! Daystar ComfortRide 2.5 Inch Front Leveling Kit part number DAYKG09101BK is correct for your 2001 Chevy 1500 2x4 and you could run tires 32" tall.

A: Hello Yes this will fit under your coil spring and will give two inches of lift. The stud adapter will thread onto the stock bolt to hold the spacer.

A: Hello Jon and thank you for your question! Daystar ComfortRide 2 Inch Front Suspension Coil Spring Spacer Kit part number DAYKF09108BK is the correct level kit for your 1994 Mazda B4000.

A: Hello Kodi, the Daystar ComfortRide 1.5 Inch Front Leveling Kit part# daykc09103bk will not work on the Dakota. The springs are a bit larger on the Ram. Thank you for your inquiry.

A: Thanks for the the question Kevin. Daystar ComfortRide 1.5 Inch Front Suspension Coil Spring Spacer Kit DAYKF09105BK Yes, this is going to be the spacer you will want to run to level your 2 wd vehicle. Thank you Answer box sales

A: Hello Yes they work fine on the heavier trucks with the diesel motors. They are a very nice spacer and easy to install on the 4WD trucks

A: Thanks for the inquiry Rey, the Daystar ComfortRide 1.5 Inch Front Suspension Coil Spring Spacer Kit part # DAYKC09103BK will allow a 31 inch tire.

A: Hello jay, Daystar ComfortRide 2 Inch Front Suspension Coil Spring Spacer Kit can run 33" tire size.

A: You can only install one leveling kit on your truck you cant stack level kits. We also recommend a longer set of front shocks to match the coil spacers. The kit works great to level the truck or for more tire clearance.

A: Hello We called Daystar they say the od is 3.5 inches across.

A: Thanks for the inquiry matt, the Daystar ComfortRide 2 Inch Front Suspension Coil Spring Spacer Kit part # DAYKF09108BK will only work up to a 1996 Ranger.

A: Hello Mark. The Daystar ComfortRide 2 Inch Front Suspension Coil Spring Spacer Kit, part # DAYKJ09111BK, will require an alignment after installation. Thank you

A: Hello Nic, the Daystar ComfortRide 2 Inch Front Leveling Kit part# daykf09108bk comes as a pair. Thank you for your question.

A: Hello McNeil, The Daystar 2 Inch Suspension Lift Kit is a 2" front leveling kit. In order to get you the correct kit part number, We will need to know your Jeeps year, make & model.

A: Thanks for the inquiry Panchio, the Daystar ComfortRide 2.5 Inch Front Suspension Coil Spring Spacer Kit part # DAYKG09101BK will fit a 2001 chevy 1500 2x4.

A: Hello Pura Vida, That's very good question. Yes, the Daystar ComfortRide 1.5 Inch Front Leveling Kit Part Number: daykf09105bk will lift the front of your vehicle 1.5" over the stock height. If you are looking to level the vehicles stance we suggest the Pro Comp Suspension 2 Inch Leveling Kit Part Number: EXP62159. Here is a direct link to that leveling kit http://jo.my/ftupe1 Thank you for the question.

A: Thanks for the question Blade Daystar ComfortRide 2 Inch Front Suspension Coil Spring Spacer Kit, DAYKF09108BK http://jo.my/cl3ede The reason the tires are wearing like this is because, they are out of alignment. When you install the leveling kit or any lift kit you will need to get the vehicle realigned. If you want to run the larger 33-34 inch tires you are going to have to do a larger lift kit or cut your fenders to make them fit on your vehicle. Thank you Answer Box Sales

A: Thanks for the question Tom, The correct way to measure the Jeep is to park the vehicle on a flat surface and measure from the ground to the rocker panel behind the front tire and in front of the rear tire. This will tell you what size spacer you will need to level your Jeep.

A: Jim, Thanks for your question. Yes the Daystar ComfortRide 2 Inch Front Suspension Coil Spring Spacer Kit will work fine on your truck and a simple alignment should be all you need. Hope this helps and I hope we earned your business!

A: Tpain, yes it will work on your Silverado we do recommend longer shocks because the factory ones will be too short. Thanks

A: Thanks for the inquiry michael, the Daystar 2 Inch Suspension Lift Kit part # DAYKJ09152BK is a coil spacer lift that will lift your vehicle 2 inches, we're not sure how you achieved the 2.5 in lift, if you combine lift you may need additional parts.

A: Thanks for the inquiry PBR, the Daystar ComfortRide 2 Inch Front Suspension Coil Spring Spacer Kit part # DAYKF09108BK will fit on qat 1991 F150 4X4, we do recommend a 2 inch longer shock due to the fact you are lifting your truck,

A: Hello John, there is a chance that you would need a spring compressor to install the 1" coil spacers.

A: Hello there, the Daystar ComfortRide 2 Inch Front Suspension Coil Spring Spacer Kit is a great kit, but if you're look for a kit with shocks they offer part number DAYKC09118BK. This combo kit is the 2" leveling kit & Scorpion Shocks. This kits offer an improved ride, more ground clearance, and the ability to run larger tires and wheels, while reducing Noise, Vibration, and Harmonics. Made in the USA

A: Hello Paul, the Daystar ComfortRide 2 Inch Front Suspension Coil Spring Spacer Kit part# DAYKF09108BK will allow you to fit a 33" tire on a 8-10" wide wheel with minor trimming. With the 12" wide wheels you might lose a little of your turning radius and have to do trimming for sure. Also our stores will install this kit and align your vehicle. Thank you for your inquiry.

A: Hello bertha, Daystar ComfortRide 2.5 Inch Front Suspension Coil Spring Spacer Kit part # DAYKG09101BK is not for you 1999 GMS Sierra 2500 2xwd. Use DAYKG09101BK.

A: Hello Mike, Thanks for the question. No other parts are required to install the Daystar ComfortRide 2 Inch Front Suspension Coil Spring Spacer Kit. An alignment is required after installation and new shocks are recommended.

A: Frank, Thank you for your question. With the Daystar ComfortRide 2" Inch Front Suspension Coil Spring Spacer Kit part # DAYKG09101BK only requires longer shocks.

A: Murphy- Thanks for the question. The Daystar ComfortRide 1.5 Inch Front Leveling Kit will fit your 02 F150 FX4.

A: Hello threegeez, Thank you for the question. Yes, you will absolutely need longer shocks.

A: Hello Trey, Thank you for the question. This part fits your vehicle: 1998 DODGE RAM 1500 PICKUP NONE V8 - 5.9 Liter - GAS. This will fit your tire size with some trimming.

A: Hello Trey, Thank you for the question. This part number will not fit your vehicle application. We do offer the Part Number: DAYKC09100BK or Part Number: DAYKC09103BK

A: Chris- Thanks for the question. No other parts are required to install the Daystar ComfortRide 2 Inch Front Suspension Coil Spring Spacer Kit. An alingment is required after installation and new shocks are recommended.

A: Nails28- Thanks for the question. The Daystar ComfortRide 2.5 Inch Front Suspension Coil Spring Spacer Kit does not require new shocks but they are recommended. I recommend the pro comp es9000 EXP916015

A: Hello Ryan, Thank you for the question. This part doesn't fit your vehicle. We do offer the Fabtech 3 Inch Spindle System w/Performance Shocks Part Number: FABK2165

A: DavidF- Thanks for the question. The Daystar ComfortRide 2 Inch Front Suspension Coil Spring Spacer Kit does not require new shocks but they are recommended at the time of install. I recommend the ES9000 http://jo.my/oxhykc

A: Mike- Thanks for the question. The Daystar ComfortRide 2.5 Inch Front Suspension Coil Spring Spacer Kit for a Chevy 2wd would work well with the pro comp es9000 EXP916015.

A: Hello Trek, Thank you for the question. Max tire size is a 32x10.50

A: Hello slidewaze, Thank you for the question. You will need a longer front shock. This spacer kit will allow you to run a 33x12.50 tire.

A: Marcos- Thank you for your question. The Daystar ComfortRide 2.5 Inch Front Suspension Coil Spring Spacer Kit can use your stock shock. As a replacement shock I would recommend a pro runner shock found here http://jo.my/l6xq1j

A: Hello Dante, Thank you for the question. This item gets you 1.5" of front lift. This is designed for the GAS motor vehicles only.

A: Texas- Thank you for your question. The kit to lift the rear of your 2012 ford F250 1.5 inches can be found here http://jo.my/u9pt5

A: Gilbert- Thank you for your question. The Daystart ComfortRide 2.5 inch front suspension coil spacer kit does not require new shocks but it is advisable. Here are the ES9000 shocks I recommend for your 94 Chevy c1500 2wd http://jo.my/rkuk25

A: Justin- Thank you for your question. You can use your stock length shocks with Daystar ComfortRide 2.5 Inch Front Leveling Kit. If your shocks are reaching the end of there life it would be a good time to upgrade. I would recommend http://jo.my/rkuk25

A: Jackson- Thank you for your question. The Daystar ComfortRide 1.5 Inch Front Suspension Coil Spring Spacer Kit will not fit your 73 dodge D-200 wd. We do not currently have a spacer kit listed for your truck.

A: Hello Alex, Thank you for the question. You can run a 32" tire with the Daystar ComfortRide 2 Inch Rear Coil Spring Spacer Kit installed. We suggest upgrading the upper control arms as well.

A: Rusty- Thanks for the question. The Daystar ComfortRide 2 Inch Front Suspension Coil Spring Spacer Kit will fit most of the 92 Ford Rangers. If you have the Twin i beam or Twin traction beam remember that if you push the wheel farther down it will wear on the out side of the tire faster.

A: Hello Woodsbuggy3, Thank you for the question. The will work just fine with one another. Just be sure the air line is correctly placed to eliminate getting cut or stretched out of shape.

A: Hello Alex, Thank you for the question. This part fits your vehicle: 1997 CHEVROLET C2500 PICKUP NONE V8 - 6.5 Liter - DIESEL

A: Hello Jftruck, Thank you for the question. Yes, the Daystar ComfortRide 2 Inch Front Suspension Coil Spring Spacer Kit DAYKF09108BK will fit your vehicle application. You will also need a longer shock when installing this on your vehicle.

A: Hello Ralphy, Thank you for the question. Yes, with the Daystar ComfortRide 2.5 Inch Front Suspension Coil Spring Spacer Kit DAYKG09101BK will allow you to run a 32x10.50 tire

A: Thank you for your question Ben. The Daystar ComfortRide 2 Inch Front Suspension Coil Spring Spacer Kit will only for the 4WD, here is a link to the installation instructions that might help you with your issue http://jo.my/a2775k

A: Hello Mark, Thank you for the question. No, you need to install this coil spring spacer with the factory isolators. That will give you 1" of lift over factory height.

A: Hello Luis, Thank you for the email. We do suggest you have the vehicle professionally aligned after installing the Daystar ComfortRide .75 Inch Front Suspension Coil Spring Spacer Kit DAYKJ09139BK

A: Rob- Thank you for your question. The Daystar 1Inch Leveling Kit replaces your factory spacer.

A: Hello adade146, The Daystar ComfortRide 2 Inch Front Suspension Coil Spring Spacer Kit DAYKC09101BK fit the 1994-2002 Dodge Ram 4WD 1500-3500 and 2003-2004 Dodge Ram 4WD 2500 & 3500. Thank you for the email.

A: Hello Grandpa's 4x4, After installing the Daystar ComfortRide 2 Inch Front Suspension Coil Spring Spacer Kit DAYKF09108BK on your vehicle we suggest professional alignment. This will eliminate any adverse tire scrub. You local 4Wheel Parts store can do the installation and alignment for you. Thank you for the email.

A: Hello gumba_fox, According to Daystar the Daystar ComfortRide 2 Inch Front Leveling Kit daykf09108bk will not fit. Thank you for the email.

A: Hello NMW, Yes, the Daystar ComfortRide 1.5 Inch Front Leveling Kit daykc09103bk will fit your vehicle application. You will need long shocks after you install this leveling kit. Thank you for the email.

A: Hello PDM, Yes, the Daystar ComfortRide 2.5 Inch Front Suspension Coil Spring Spacer Kit DAYKG09101BK will fit your vehicle application. Thank you for the email.

A: Hello TexasHybrid, The Daystar ComfortRide 1.5 Inch Front Suspension Coil Spring Spacer Kit DAYKF09105BK will level the vehicles static ride height. Thank you for the email.

A: Hello Doreen, You are correct. This is a coil spring leveling spacer kit. Nothing is needed for the rear of the vehicle. It simply raises the front of the vehicle so it is level with the rear. It eliminates the factory forward rake. If you have any further questions please feel free to ask. Thank you for the email.

A: Hello Dean, Yes, with the Daystar ComfortRide 2 Inch Front Suspension Coil Spring Spacer Kit DAYKF09108BK you will gain 2 inches of lift height over your current suspension height. Thank you for the email.

A: Hello Alex, The Daystar ComfortRide 1.5 Inch Front Suspension Coil Spring Spacer Kit DAYKC09103BK will fits your vehicle: 2012 DODGE 1500 2WD. Thank you for the email.

A: Hello Matt, Yes, the Daystar ComfortRide 2 Inch Front Suspension Coil Spring Spacer Kit DAYKC09101BK will fit the 2012 Ram 1500 2WD. Thank you for the email.

A: Hello luis, Yes, the Daystar ComfortRide 2 Inch Front Suspension Coil Spring Spacer Kit DAYKF09108BK will fit the 1994 FORD F-150 PICKUP. Thank you for the email.

A: Hello SilverBronco, Unfortunately you can not stack the Daystar ComfortRide 2 Inch Front Suspension Coil Spring Spacer Kit DAYKF09108BK with your current 6 inch suspension lift. If you looking for a little more wheel well clearance I would suggest the 2 Inch Body Lift PER842 http://jo.my/kiflse or 3 Inch Body Lift PER843 http://jo.my/9ukcb1 Thank you for the email.

A: Hello Shane, With the Daystar ComfortRide 2 Inch Front Suspension Coil Spring Spacer Kit DAYKF09108BK no I-Beam drop brackets are needed. You will only need longer front shock. Here is a direct link to our shock options http://jo.my/shocks

A: Hello Gabe, Yes, the Daystar ComfortRide 2 Inch Front Suspension Coil Spring Spacer Kit DAYKC09101BK will fit a 2011 RAM 3500. Thank you for the email

A: Hello Arab, Yes, the Daystar ComfortRide 2 Inch Front Suspension Coil Spring Spacer Kit DAYKC09101BK will fit the 2007 Dodge Ram 1500 2WD. Thank you for the email

A: I would recommend the Bilstein 5100 series shocks you can find the front here http://jo.my/nk7ih0 and the rear here http://jo.my/95acxk

A: rick, We only offer the Daystar ComfortRide 2 Inch Front Suspension Coil Spring Spacer Kit DAYKF09108BK for the 1995 Ford F150

A: The Daystar Comfort Ride 2 Inch Front Suspension Coil Spring Spacer Kit will fit 2WD and 4WD Ranger and Bronco II

A: kelly the Daystar spacer kit is all that is needed in most applications ad the truck uses a coil strut assembly and the spacer goes on top of the assembly so no shocks needed.

A: Mark Mercado, We recommend the Revtek 2 Inch Torsion Key Leveling Kit REV625 for your 2003 Ford F-150 Super Crew 2WD 4.6L. Here is a direct link http://jo.my/f150levelingkit