Dana Spicer Heavy Duty Axle U-Joints

A: It fit my 09 jk rubi

A: Yes, the Dana Spicer SPL30 Series U-Joint - 5-7166X fit 44 Axles | NOTES: 4WD; Rubicon; Unlimited Rubicon; with Inside Snap Rings; Inside Snap Ring Dimension of 2.406in; with Cap Diameter 1.188in;

A: The Dana Spicer 1480 Series U-Joint - PN: D/SSPL55X is non-greaseable | The Dana Spicer Universal Joint Set - PN: D/S5-1480SPX-MK is the greaseable design.

A: The Dana Spicer 1310 Series U-Joint - PN: 5-1310X Fits the 1999 Jeep Grand Cherokee | Rear Driveshaft at Transmission RWD; Rear Driveshaft at Rear Axle RWD; Rear Driveshaft at Transmission 4WD; Rear Driveshaft at Rear Axle 4WD; Front Driveshaft at Front Axle 4WD; Front Driveshaft - CV at Transfer Case 4WD.

A: The Dana Spicer 1310WJ Series U-Joint - 5-760X Fits: up to 2011 Jeep Wrangler (JK) Sahara USE: The 2015 Jeep Wrangler 4WD;with 1310 Aftermarket Drive Shaft; Rear Driveshaft at Transmission | Rear Driveshaft at Rear Axle | Front Driveshaft at Front Axle | Front Driveshaft - CV at Transfer Case Part Number; 5-1310-1X Universal Joint

A: I am not showing this fits your JK: https://www.danaaftermarket.com/spl-automotive/automotive-driveshaft/universal-joints/part/axle-shaft-universal-joint/SPL55-1480XC?cat1=0&str=SPL55-1480XC&cp=0&catalog=PIMS_NA&partType=PART

A: A 2011 JK Sport takes a D/S5-760X drive axle u-joint for each side if you have stock axle shafts.

A: Tom Woods could have built their driveshaft for the JK with a 1310 series u-joint and that would most likely accept the D/S5-1310X. This is a sealed for life u-joint. It has external snap rings, it has 1.062 diameter bearing caps and is 3.219 inches wide. If he has the more heavy duty 1350 series driveshaft, then that would most likely use a D/S5-1350x. This is a sealed for life u-joint. It has external snap rings. It has 1.188 diameter bearing caps and is 3.625 inched wide.

A: No, those phrases are used interchangeable. You don't need to modify anything. This U-joint is listed to fit your TJ/LJ front axles at the wheels. So between the inner axle shaft and the stub shaft at the wheel hub.

A: We need a little bit more information on your truck and the axles you are running, and what you are looking for. Please reach out to our sales line Toll Free: 1-877-474-4821

A: I'm not sure what your question is, but with this particular question, we are going to need some more information. Will what work on what vehicle? What are you looking for? Please call our sales line to assist further Toll Free: 1-877-474-4821

A: This U-joint does not fit a 1991 Nissan D21 Hardbody pick up.

A: No this will not. This is for AAM (American Axle Manufacturing) applications: GM, Chevy, Dodge Ram

A: Hello Billy, Dana Spicer SPL30 Series U-Joint - 5-7166X fit both the Dana 30 / 44 Axles. The Jeep CJ7 came with a Dana 30 Front Axle.

A: Hello Rickey Yes they are the correct u-joints for the drive shafts. If you need them for the axle shafts up front they would be d/s5-260x thanks

A: Hello Scott Yes this one is non greasable if you want greasable use D/S 5-153x Thanks

A: Hello Nancy Yes this will fit the transfer case and the axle on your Jeep. Thanks

A: Hello Zach A 2013 JK takes a D/S5-7166X Front Drive Axle U-Joints Thank You for your question

A: Hello Yes this is the correct joint for the front drive shaft. There is also part number D/S 5-1310x that works non greaseable. Thanks

A: Hello Andy Yes the 5-760x is the correct axle joint for your 1500 Ram Thanks

A: Hello The number you need is the 5-1330x for your drive shaft. Thanks

A: Hello Ryan The correct part number for the Dana 60 axle joint is D/S SPL55-3x here is the link http://www.4wheelparts.com/Drivetrain-Differentials/Dana-60-Heavy-Duty-Axle-U-Joint.aspx?t_c=12&t_s=237&t_pt=101013&t_pn=D%2fSSPL55-3X thanks

A: Hello This joint is for the Chrysler AAM axle the Dana 60 joint is part number D/S SPL55-3x It is the Spicer Life series also. Thanks

A: Hello Victor, Yes, this will replace your factory u-joints. This is a high quality unit and about the cheapest u-joint we offer for your vehicle. Thank you.

A: Hello Rick The correct part number for your AAM axle is D/S 5006813 http://www.4wheelparts.com/Drivetrain-Differentials/AAM-9-25ion-Heavy-Duty-Axle-U-Joint.aspx?t_c=12&t_s=237&t_pt=101013&t_pn=D%2fS5006813 Thanks

A: Hello Gunny Yes these are the correct U-Joints for your Super Duty and yes you do have a Dana 60 front axle. Thanks

A: Hello The 1310 is the small series for Jeeps and 1500 trucks. Your truck has 1410 u-joints now in the rear shaft and 1350 in the front. The rear u-joint's are part number D/S 5-160x and the fronts are D/S 5-178x Thanks

A: Hello LJ Yes it is the correct u-joint for you axles. Thanks

A: Hi Maneval Your Cherokee will take a D/S 5-1310X ujoint in both the front and the rear driveshafts Thank You Jon Snyder 4Wheelparts

A: Hello Yes these are for the 2007 and newer Jeep Rubicons all models. Thanks

A: Hello The early front ends used the Dana 5-260x u-joint the later 95 up Dana 30's used the 5-760x u-joint. 5-260x 2.1880 between snap rings and cap size 1.0620 5-760x 2.1880 between snap rings and cap size 1.1880 Thanks

A: Hello Yes this is the U-joint you will need for your axles. Thanks

A: Sir, yes that is correct u-joint for your Jeep YJ. Thank you for your question.

A: Hello The GM axles use a 3R series u-joint part number 5-3147x. Thanks Rody

A: Thanks for the question. Yes, this will fit on you vehicle. Thank you

A: Hello Markus, we do not have a application guide that covers the Crv. Please contact your local Honda dealer to determine which u joints u need. Thank you for your inquiry.

A: Hello Chandler Yes that works for your Bronco on the rear shaft at the axle. Thanks

A: Hello Lyn Yes this joint will work in all positions on the drive shafts. The only different U-Joint would be for the axle joints at the wheel ends up front. The axle joints if needed would be D/S 5-260X Thanks

A: Hi Bob The Dana Spicer D/S5006813 is not the correct U-Joint for your Ram 1500 that U-Joint is for the 3/4-1 ton trucks. Your 1500 will use the standard D/S 5-760X U Joint http://jo.my/mgy4aw. Thank You

A: Hi Big Blue The Dana Spicer 5-760X U-Joint is the correct replacement for your 1986 K20 front axle Thank You

A: Hello The Dana joints are non greasable on most of their axle joints. The greasable version of this joint is no longer being made by Dana. The major problem with the greasable U-joints is they drill through the cross. When they do this it weakens the U-joint by 20 to 30 percent.

A: Hello Yes the 5-760x is the correct u-joint for your axles.

A: Thanks for the question Malcoim Dana Spicer 1330 Series U-Joint d/s5-1204x Yes, this will work for your rear driveshaf, on the axle side. Thank you Answer box sales

A: hello The Dana number you need for the axles is D/S5-7166x

A: Hello Kolby, the Dana Spicer Dana 30 Small 44 Spicer Axle U-Joint part# D/S5-260X is the correct replacement u joint for your front axle. Thank you for your inquiry.

A: Hello No that number is not correct the one you need is the D/S 5-760x

A: Hello Yes that u-joint will fit the stack drive shaft.

A: Hello The u-joint for your drive shaft would be part number 5-1310x in the perma-lube series.

A: Hello Chris Yes that is the u-joint you need for your Jeep. Thanks

A: Hello Richard, Thank you for the question. This u-joint is a heavy duty factory replacement for your vehicle. I stronger option would be the CTM Racing Dana 44 U-Joint Part Number: CTMC144-1881

A: Hi Paul Yes the D/S5-7 X u joints will fit your Jeep TJ with the factory Dana 30 axle shafts. Thank You

A: Hi Sam Your 2005 Dodge used a drive shaft from AAM and we do not have a Spicer equivalent for that joint at this time. You may wish to try the dealer for a quality joint Thank You

A: Hello Eric, Thank you for the question. Yes, this u-joint will fit your vehicle application.

A: Hi Mike The 5-760X is an Axle u joint not a driveshaft joint your 2000 Jeep TJ will use 1 D/S5-1310X http://jo.my/2ej01u and 2 D/S5-1310-1X joints in the CV at the Transfer case Thank You

A: Hi Nick The D/S5-760X U-Joint will fit your Jeep JK Dana 30 front axle. Thank You

A: Hi Don The correct Axle U-Joint for your 2008 Jeep JK Wrangler Rubicon is the D/S5-7166X U Joint which is a larger Joint. This Joint is not yet live on our site but is in stock in our warehouses and runs $80.99 Thank You

A: Fermloks- Thank you for your question. The Dana Spicer 1310 Series Heavy-Duty U-Joint was used at the axle end for most applications. Measure your current U joint. The 1310 Joint has the measurements of Cup Size A= 1.062in.; Cup Size B= 1.125in.; Outside To Outside= 3.2190in

A: Hi Brandon The 3R joint will fit the front drive shaft but the rear is a much larger D/S5-3206X that we do not list on our site. please call our mail order department Toll-Free: 877-474-4821 for pricing and availability. this is a socking part number in our main warehouses Thank You

A: Hi Joe The correct Axle U-Joint for your Jeep JK is the D/S5-7166X. the cost of this Axle U-Joint is $80.99 each and is not listed on out site ate this time. This Joint is larger than the D/S5-760X. These are in stock in quantity. Thank You

A: Hi Cody This u joint will work at the rear axle end of the shaft but there is a option of two joints at the t/c end of the shaft. the book does not state which one is correct you will have to measure your existing joint and compare . the other option is the D/S5-790X Joint which is not listed on our site. Thank You

A: Hi Ernnn Your truck used a combination of U Joints depending on tow rating ic could use the D/S5-1310 U Joints in some locations as well as the 3R U Joints D/S5-3147X in other locations please check the cross the joint measurements and compare them thank you

A: Hello tman, Thank you for the question. This is the correct part number.

A: Hi James This is the correct U-Joint if your Jeep is not equipped with the Selec-Trac system. If you have Selec Trac you will require a 5-213X joint at the top rear at the T/c Thank You

A: Hi Caddy This D/S5006813 are the correct U-Joints for your 2010 Dodge Ram 2500 front axle. Here is a link to Dana Spicer U-Joint spec sheet. http://jo.my/mvmhzz Thank You

A: Sarah- thanks for the inquiry. Yes the Dana Spicer 1310 u-joint would be the correct u-joint for your 2004 Jeep Wrangler X

A: Hi Doc These are the correct for your 1998 Jeep TJ drive shaft U-Joints if you still have the factory drive shafts. Thank you

A: Alex- Thanks for the inquiry. I'm sorry but I don't have any Spicer listings for your Foden Alpha 3000.