Manufactured from 3/16" steel plate, sculpted to enhance the styling of the JK platform, compact design does not over power the front of the Jeep. Integrated winch plate with fairlead mounts, integrated shackle mounts for recovery points and grill guard are included. Four light mounting points for auxiliary lights. Easy bolt installation, no drilling required. Black textured power coat finish. Shown with optional JK-5123 skid plate.
I've had the bumper on for about 6 months now and it's still as FRESH as it was when it was first installed. It's a good, solid bumper and luckily when I got it - it was on a 4wp sale! Now I'm looking to adding lights and a winch, I would highly recommend to get the skid plate (sold separately) just to make it look even better!
By Rob from Rio Grande Valley
Solid Bumper; Poor Instructions and Fit
Bumper is heavy. Installation instructions are horrible. The front passenger mounting holes were off - they did not line up with the passenger side mounting bracket on 2014 Jeep Wrangler and bottom mounting holes were so close to the weld that the bumper could not be modified; had to grind off 1/4 inch of mounting bracket on the jeep.
For installing the side bolts, do NOT drill into the Jeep mounting bracket until after you have installed the front mounting bolts, otherwise you'll be putting multiple holes in the frame. Use the existing side hole on the bumper as a guide of where to drill the hole in the frame.
By Michael from Dallas
Very solid and good looking bumper with winch mount. Difficult to install. Excessive weld would not allow for precise fitment. Had to alter the frame mounting points by grinding and drilling the four hole plates. Side attachment bolts did not line up. Had to drill new holes.
By Grey Ghost from Central Florida
Solid Product Overall
Everything has been great in the 2 weeks I've had this bumper on!
Only gripe I had was during installation discovered that the bolts that come with the bumper are too short and there is absolutely no way to get both the regular AND lock washer on there. Opted to just go with the lock washers.
Hopefully it doesn't fall off anytime soon!
By The Huntsman from Austin, TX
realy should have had instructions, grill bar should have the mounting nuts welded into bumper.
be sure to attatch bar prior to mounting or enjoy doing it twice. drill out bumper mount holes in frame,of jeep to ease allighnment.realy good construction as I use my winch a lot
By HD blue from alberta canada
even following directions bolt holes not even close to lining up.dont buy this bumper unless you have alot of extra time
By parker from grove city,pa
THE BUMPER WAS EASY TO INSTALL.I USED A ATV JACK TO LINE UP.THE SIMPLE WAY TO INSTALL THIS BUMPER BY YOURSELF.THE ONLY PROBLEM I ENCOUNTER WAS THE BOLTS WERE A LITTLE TO SHORT,SO I INSTALL ALL THE BOLTS WITHOUT THE WASHERS AND SNUG ALL THE BOLTS UP, THEN WENT BACK AND REINSTALLED THE WASHERS,THIS WORK PREFECT.I ALSO INSTALLED A X2O WINCH ON THIS BUMPER AND IT LINED RIGHT UP.IT WAS A PREFECT MATCH.NOW MY RUBICON LOOKS LIKE A JEEP.
By SANDBAGGER from LAS VEGAS,NV
Install was a breeze, Looks great, light and a lift kit comming up. 4 wheel parts is the only place i shop
By Milkman in Dallas from Dallas TX
Best bang for the Buck!
[...] It was easy to install and directions were clear. [...] I will always buy from you!
By "Hole in One Jeep" Bill from Chesapeake, Virginia
Great bumper looks awsome. bolts were a little short during installation but just didn't use some of the washers. it looks great though and all holes for lighting and winch are predrilled nicely poweder coated.
What is required to drill when installing on a 2010 JK?
Roger from on
Hello Roger, The Body Armor 4x4 JK Wrangler Front Winch Bumper with Grill Guard in Textured Powder Coat will require you to open the mounting holes.
Dave from on
was wondering if I would have to relocate the brake pump canister to install this bumper
Rome from United States on
Hello Rome, The Body Armor 4x4 JK Wrangler Front Winch Bumper with Grill Guard in Textured Powder Coat part# B/AJK-19531 comes with the relocation kit. You will not need to purchase anything else. Thank you for your inquiry.
mikey from United States on
Just installed the bumper - looks great on my 2010 Jeep Wrangler Rubicon. What lights are captioned in the photo? Do you have any recommendations? Also, what is the best way to hide the wiring and best way to drill holes for license plate bracket. Thanks.
Robert from McAllen, TX on
Thanks for the inquiry Robert, the Body Armor 4x4 JK Wrangler Front Winch Bumper with Grill Guard in Textured Powder Coat part # B/AJK-19531 pictured are the piaa part # PIA05196, really you can ose any light on the market, pro comp, KC, Rigid, ARB, Hella, a 6 inch round would be a good suit.
Body Armor 4x4 produces extreme off-road equipment for Jeeps and trucks. The company was founded in the 1990s in Corona, California. Body Armor engineers its products to withstand the abuse of the trail over and over while personalizing the look of your rig. Body Armor popular products include Jeep bumpers with integrated winch plates and multiple light mounting points, Trail doors that are predrilled for aftermarket mirrors plus thick nylon webbing to protect passengers from scraping branches and a very secure two position latch, plus rock steps that also function as sliders. All Body Armor parts are built for durability with a dual process powdercoat oversprayed with a textured finish and undersprayed with an e-coat. So corrosion resistance is quite strong. Shop Body Armor 4x4 Now