great product, fit easily into my Truck, All parts needed were there
Purchased this from the 4 Wheel Parts in Coppell Texas over the weekend and installed it the next day. Installation was pretty quick and easy (except for getting the temp sensor out of the stock intake hose). Total time for install was less than one hour. Could really tell a difference in acceleration from a stopped position as well as acceleration while passing on the freeway. Nice throaty tone while accelerating as well, but not over the top. Very happy with the gain in lost power from adding the 4 inch lift and 35 inch tires!
from Dallas, Texas
Easy to install unless you are picky as I am about installs. I had to redo couple times because of wanting to reroute some electrical wires from the winch. Other than that it's an easy install. After installing a similar (NOT Airaid) product on a friend's Jeep, I noticed the high quality and stability of this one. I've just added it to my rig so not sure of MPG differences. I'm sure it will increase. This, along with the Airaid throttle body spacer, the throttle response is incredible! So Glad I purchased this one!
from Maiden, NC
Gained horsepower and fuel mileage, instructions easy to follow
and install quick less than an hour. Oh sounds great too!!!
from Litcfield Park, Az
5.0Great air filter system
Detailed instructions provided that makes installation a snap (about 30 to 40 minutes). A benefit I wasn't expecting was it really enhanced the sound through the exhaust making my Raptor sound more throaty than before. Throttle response is improved and gas mileage seems to be a bit better. I have used AirRaid in the past and truly like this filter system
from Scottsdale, AZ
5.0Does the Job
This intake is a great way to improve the performance of your Chevy truck and improve fuel economy at the same time. It replaces the restrictive factory intake with an open-element style performance air filter with cold air dam panels that keep the filter isolated from hot engine compartment air while adding plenty of cool outside air. The replacement intake tube further optimizes airflow to the engine and has places for all of the factory tubes and sensors to bolt up. The system sounds great when you step on it and I really saw an improvement in part throttle response.
By Ricky B.
from Tallahassee, FL
Just take a look at the air filter used in this kit; it's MASSIVE! This cold air intake replaces the restrictive factory intake with a free-flowing cold air system that gets more air to the engine and lets it breathe. I'm really impressed with the quality of the materials used and the installation was really easy; absolutely everything needed was included in the box. I coupled this intake with an exhaust system and saw a huge improvement in power, and even picked up a solid MPG. I'd recommend this to anyone!
By Dirty Rod
from Peoria, AZ
Installed under 30 minutes. Made truck sound better. Engine breathes much better. Acceleration improved. I would recommend this for any F150 truck owner.
THIS PART IS RESTRICTED FOR SALE IN THE STATE OF
CALIFORNIA AS REGULATED BY THE CALIFORNIA AIR
RESOURCES BOARD, ALSO KNOWN AS (C.A.R.B). 4
WHEEL PARTS HONORS THIS RESTRICTION AND WILL NOT
SELL OR SHIP TO ANY ONE OR ANY DESTINATION IN THE
STATE OF CALIFORNIA.
Thanks for the question Clark
MXP Series Synthaflow Cold Air Dam Intake System eve200-285
According to the manufactures dyno sheet it is approximately 21 HP and 30 torque.
Here is the link to the manufactures dyno sheet. http://jo.my/5nbei5
Answer box sales
will this intake fit onto a 3.8l that is a gulf specification (GCC)? It has an additional fan between the radiator and the engine that the American spec doesn't have. will the fan cover obstruct the intake tubing?
JKU 2008 GCC specs
Answer this question
Talking to AirAid they say there is no clearance issue. That is up above the shroud and won't be in the way.
Thank you for the question. This part fits your vehicle: 2007 NISSAN XTERRA S V6 - 4.0 Liter - GAS
Would you wait to install this when adding new exhaust, or could this be added by itself? I've read on some F150 forums that you also need to tune the engine, but I thought that could void your warranty? Thoughts?
Answer this question
Thank you for the question. You can install this prior to exhaust installation. The factory (Computer) ECU will self adjust when installing this and the exhaust.
i own a 2003 chevy 2500HD and i would like to put on the airaid cold air intake (201-145) with the Airaid throttle body spacer (200-512-1)would i have to do any mods to either one? I ask because i did the same to my Toyota Tacoma and had to cut off 1/2 inch on the intake tube to make it fit with any binding.
Answer this question
Thanks for the inquiry. There should be no modification invlolved in running the Airaid Cold Air intake and throttlebody spacer at the same time on your Chevy 2500HD
Since 1997, AIRAID has manufactured high quality air intake systems that are the result of thorough research and development and advanced engineering. Their goal is to produce innovative, easily installed kits that radically increase airflow, torque and horsepower as they up overall engine performance. Jeep owners appreciate AIRAID air intake systems appearance, functionality and how easy they are to install. Extend the life of your Jeep whether it's a Wrangler, Cherokee or Comanche. When you want to feel your engine breathing easier and releasing loads more horsepower, choose AIRAID components for your performance upgrade or replacement. Shop AIRAID Now