• Community
    • Team 4 Wheel PartsJoin the team and keep up with Greg Adler
    • FacebookAccess exclusive off-road news and giveaways
    • TwitterStay posted on 4 Wheel Parts events
    • YouTubeSee product, installation, and event videos
    • Google+Get the inside scoop on the latest off-roading trends
    • InstagramCheck out exclusive photos
    • Sign Up for Email Offers

Drivetrain & Differential Glossary of Terms

With terms like Axle Shafts, Ball Joints, ull Floater Gaskets, and Limited Slips, drivetrain lingo can get confusing quickly. Fortunately our experts have put together a thorough glossary of terms to help you learn.

A glossary of terms for various drivetrain-related items, including Axle Shafts, Ball Joints, Bearings, C Clips, Calipers, Carriers, Carrier Bearings, Cross Shafts, Crown Gears and more.

A

  • Axle Shafts and Axle Kits

    Axle Shaft - An Axle Shaft is the part of an axle assembly that is turned by the side gear of the differential and transfers the power either directly to the wheel or to the wheel hub that the wheel is bolted to, depending on the style of axle.

    Find: Axle Shafts and Axle Kits

  • Ball Joints

    Ball Joint - Ball joints connect the steering knuckle to the axle housing, or arms, and hold it in position while allowing the steering motion.

    Find: Ball Joints

  • Banjo - A Banjo refers to the type of axle housing that utilizes a drop out third member.

  • Ring and Pinion Installtion Kit

    Bearing - A Bearing provides a low friction surface that allows two parts to move on a single axis.

    Find: Ring and Pinion Installation Kit

  • C Clip - “C” clips are commonly used on semi-floating axles to retain the axle shaft. On the spline of the axle shaft there is a receiver groove cut into the end for the C clip to grab the axle. There is a pocket machined into the side gear of the carrier that the OD of the C clip fits into. With the cross shaft removed, the axle is inserted into the side gear. At this point the C clip is placed onto the shaft and the shaft is pulled out until the clip is seated in the pocket. Now the cross shaft is reinserted and the axle can no longer move in or out except for its appropriate end play.

  • Force 10 Brake Kit

    Caliper - Referred to as a brake caliper, it applies pressure on a spinning disc (rotor) to slow a vehicle.

    Find: Force 10 Brake Kit

  • Calipers - Also referred to as Vernier Calipers. A tool used to take precise measurements in thousandths of an inch.

  • Differential

    Carrier - Sometimes referred to as a Differential Case or Ring Gear Carrier. This unit transfers the motion from the ring gear to the axle shafts.

    Find: Differential

  • Ring and Pinion Installation

    Carrier Bearing - These are the bearings that ring gear carriers ride on. May also refer to the driveshaft support bearing used in multiple-piece driveshafts.

    Find: Ring and Pinion Installation Kit

  • Chromoly - Chromoly is an abbreviation for “chromium-molybdenum steel.” Sometimes called Chro mo. This material is known for its malleability or flexible memory and tensile strength.

  • Power Trax Performance Corss Shafts

    Cross Shaft - The cross shaft is a hardened pin that transfers a load from the carrier case to the spider gear assembly.

    Find: Power Trax Performance Cross Shafts

  • Ring and Pinion

    Crown Gear - Commonly known as ring gear, it is the gear that is bolted to the carrier and driven by the pinion gear, thereby turning the carrier.

    Find: Ring and Pinion

  • Ring and Pinion Installation Kit

    Crush Sleeve - Also called Crush Collar, this is a collapsible spacer placed between the inner and outer pinion bearings to keep a preload on them.

    Find: Ring and Pinion Installation Kit

  • Coast Side - The Coast side of the gear tooth is the concave side. The coast side is loaded when the vehicle is decelerating or in reverse. The exception to this rule is in standard rotation front axles where it is the driven side.

  • Concave - An Inward curving surface, like a bowl.

  • Convex - An Outward curving surface, like a crown.

  • CV - A slang term short for Constant Velocity. A type of axle shaft mainly used in independent suspensions requiring a smooth, long travel axle. The Term CV, when used to describe a driveshaft or propeller shaft, is referring to a Double Cardin Joint. The Double Cardin Joint looks like two U-Joints in close proximity to each other and is used in shafts that have harsh angles on them.

  • Dial indicator - An instrument used for tracking precision measurements down to 1 thousandth of an inch.

  • Differential

    Differential - The differential is a device that usually consists of gears. These gears allow each of the driving wheels to rotate at different speeds, while supplying equal power to each of them.

    Find: Differential

  • Drag - Drag is a load or resistance keeping something from turning freely.

  • Drive Side - The Drive side of the gear refers to the convex or crowned side of the ring gear. This side of the gear is the side of the tooth that the pinion gear pushes off to turn the ring gear when accelerating forward. This holds true in all but standard rotation front differentials where it is reversed.

  • Currie High Pinion

    Drop Out - The drop out refers to a particular type of axle that has a separate gear case assembly that can be removed from the housing (picture A). This is opposed to an axle that has the gears installed into the physical axle housing (picture B).

    Find: Currie High Pinion Assembly

  • Flange - The word Flange is used to describe many different items in a vehicle, but generally it refers to a flat mounting surface to couple two pieces together.

  • Full Floater - Full Floater is a term used to describe a type of axle retention system. The full floater axle is a non-load carrying axle that does not have a wheel mounted to it. This axle usually bolts to a wheel hub that rides on a set of bearings on a spindle that is part of the axle housing. It is called a full floater because the axle requires no support, and thus it is “floating” between the wheel hub and the side gear.

  • Gasket - A Gasket is a type of seal between two mating surfaces preventing leaks.

  • Heal - The heal is the part of the ring gear tooth that the pinion contacts first. This is the very outside of the gear tooth.

  • Currie High Pinion Assembly

    High Pinion - High pinion is another name for the reverse rotation gear sets. This term refers to the fact that the pinion of the axle is above the centerline of the axle housing.

    Find: Currie High Pinion Assembly

  • Axle Assembly

    Housing - This term refers to the main body of the axle assembly.

    Find: Complete Front Axle Assembly

    Find: Complete Rear Axle Assembly

  • Hub - The word “hub” describes a number of things, but in our automotive world it describes a wheel mounting device that transfers power to the wheel. This is not to be confused with a locking hub, which is called a hub as well. This unit usually is supported by two bearings and is driven by the axle shaft.

    Locking Hub Kit

  • I.F.S. - I.F.S. is short for Independent Front Suspension. This type of suspension allows each wheel to move independently of each other over an obstacle.

  • I.R.S. - Short for Independent Rear Suspension. This type of suspension allows each wheel to move independently of each other over an obstacle.

  • Axle Kit

    Inner Axle - Inner axle refers to the innermost axle shaft of a two-piece axle assembly.

    Find: Axle Kit

  • King Pin - King pin is a type of steering knuckle pivot. This system shares the same job as a typical ball joint but is believed to be stronger than the ball joint. This system has basically been phased out by ball joints.

  • Knuckle - The steering knuckle is the main component that allows a solid axle to perform its steering function. The knuckle is usually retained to the housing by the ball joints or king pins.

  • Differential

    Limited Slip - The Limited Slip is basically a preloaded open differential. Also known as a Posi, these units usually use a set of clutch springs to preload the spider gear set between 150-450 ft. lbs. This preload provides a breakaway setting. This breakaway is the force required to allow the axles to differentiate.

    Find: Differential

  • Locker - Most lockers use a type of ratcheting devise to lock the axles together when power is applied to the unit and allow one wheel to disengage while turning. These units are suited for the more aggressive wheeler as these units do have some drivability concerns. Although minor, these units usually clunk and bang but are better suited for the street than a spool. These units will turn both tires even if one is off the ground.

    Find: Differential

  • Locking Hub Kit

    Locking Hub - The locking Hub is a device that allows the wheel bearing hub to be disengaged from the axle shaft. This function is used in part time 4 wheel drive vehicles to reduce the additional drag of the drivetrain when the 4 wheel drive is not needed.

    Find: Locking Hub Kit

  • Mini Spool

    Mini Spool - A mini spool is a device that goes inside a factory differential carrier, replacing the spider gear assembly and converting it into a spool. A full spool is a one-piece unit that replaces the carrier as well. Neither provides a differential action between the shafts.

    Find: Mini Spool

  • O.E.M. - O.E.M. is short for Original Equipment Manufacturer or original factory stock part.

  • Axle Kit

    Outer Axle - Also referred to as a stub axle, it is the outermost axle shaft of a multiple shaft assembly.

    Find: Axle Kit

  • Pattern - Pattern refers to contact pattern between the gears. This contact pattern is used to see how the pinion gear is contacting the ring gear. By reading this print, you can determine if different shims are required to set up the proper gear mesh.

  • Ring and Pinion

    Pinion Gear - The pinion gear is the drive gear that turns the ring gear

    Find: Ring and Pinion

  • Pinion Angle - Pinion angle refers to the angle that the axle yoke is at compared to the drive shaft and the transfer case or transmission.

  • Pinion Pre Load - Pinion Pre Load is the amount of drag that is required to turn the pinion shaft. Drag is a load or resistance keeping something from turning freely

  • Pinion Yoke - Pinion Yoke is a part that connects the pinion shaft to the drive shaft.

  • Posi - Posi is another name for a Limited Slip. The Limited Slip is basically a preloaded open differential. These units usually use a set of clutch springs to preload the spider gear set between 150-450 ft. lbs. This preload provides a breakaway setting. This breakaway is the force required to allow the axles to differentiate.

  • Preload - Pre load or drag is a load or resistance keeping something from turning freely.

  • Race - The Race, or cup as it is also called, is a press-in hardened surface for a bearing to ride on.

  • Ratio - A ratio is a quantity that denotes the proportional amount of one quantity relative to another.

    Example: If your drive shaft turns four times for every one turn of the wheel, your gear ratio is 4 to 1 or 4:1.

  • Ring and Pinion

    Reverse Rotation Gear - The reverse rotation gear set was developed for use in front axle applications. The standard gear, when used in a front application, is running in reverse. This means the coast side of the gear is being used as the drive side. The convex (Drive) side of the gear is capable of carrying more load than the concave (coast) side. On a reverse ring and pinion, this problem has been corrected to create a stronger axle assembly. This was also done to help with driveline angles and reduce vibration.

    Find: Ring and Pinion

  • Ring and Pinion

    Ring Gear - The Ring Gear, also known as a Crown Gear, is the gear that is bolted to the carrier and driven by the pinion gear, thereby turning the carrier.

    Find: Ring and Pinion

  • Run Out - Run out is an undesired movement of a part through its motion, or wobble.

  • Rotor - Referring to a brake rotor, this is the part that the brake caliper clamps down on to slow the vehicle.

  • Root - The Root, or Flank, of a gear tooth is the very bottom or base of the tooth that spans the gap between the teeth.

  • R.P.M. - RPM is short for Revolutions Per Minute.

  • Semi Float - A semi-floating axle is one that is supported at the inner spline end then is supported by a bearing before the outer end, carrying vehicle weight.

  • Shim - A shim is a thin piece of material used to fill small gaps or spaces between objects. Shims are typically used in order to support, adjust for better fit, or be used as spacers to fill gaps between parts.

  • Side Gear - The Side Gear is an internally splined gear that receives the axle shaft. The spider pinion gear then drives this gear.

  • Spanner - The Spanner is also known as a side bearing adjuster. This adjuster is used to move the carrier assembly side-to-side to set back lash.

  • Spanner Wrench - The Spanner wrench is used to grip and turn the spanner nut.

  • Differential Internal Kit

    Spider Gear - Spider gear is also called spider pinion gear. These are the small gears that make up the spider gear assembly. This assembly is usually made up of two side gears and between 2 –4 spider gears. The spider pinion gears are driven by the cross pin of the carrier.

    Find: Differential Internal Kit

  • Spline - Splines are the raised portions that look like teeth. Splines provide a strong and effective way of easily joining two parts together that will need to be removed at a later date. Splines are usually seen as an external (male) and internal (female) receiver variety.

    External Spline
    Internal & External Spline

  • Auburn Gear Full Spools

    Spool - A spool is used to permanently lock axles together. Spools are usually used in competition vehicles that require no differential action between the axles. Spools are not recommended for street use.

    Find: Auburn Gear Full Spools

  • Steering Knuckle - The steering knuckle is the main component that allows a solid axle to perform its steering function. The knuckle is usually retained to the housing by the ball joints or king pins.

  • Axle Kit

    Stub Axle - The Stub Axle is the outer most axle shaft of a multiple shaft assembly.

    Find: Axle Kit

  • Currie High Pinion Assembly

    Third Member - Also referred to as Drop Out. The drop out refers to a particular type of axle with a separate gear case assembly that can be removed from the housing (picture A). This is opposed to an axle that has the gears installed into the physical axle housing (picture B).

    Find: Currie High Pinion Assembly

  • Toe - The Toe of the gear tooth is the inner half closest to the carrier. This is the part that sees pinion contact last.

  • Torque - Torque is the rotational force needed to move an object. In our case, it refers to the amount of force needed to turn a bolt or pinion. Torque is measured with a special tool called a Torque Wrench.

  • Torque Wrench -A Torque Wrench is a special tool that is used to measure the amount of force required to turn a bolt. This torque is measured in either in foot pounds or inch pounds depending on the quantity of force needed. There are a variety of different types of torque wrenches, but the two most common are the bar graph and the click types.

    Bar Graph Torque Wrench
    Click Type Torque Wrench

  • U-Joint - U-Joint is short for Universal joint, also known as a Cardin joint. The U-joint allows a rigid shaft to bend in any direction. It consists of a pair of hinge-like crosses located close together, but oriented at 90° relative to each other.

  • Vernier Calipers - Also referred to as Calipers. A tool used to take precise measurements in thousandths of an inch.

  • Wheel Hub - The word “hub” describes a number of things. In our automotive world, it describes a wheel mounting device that transfers power to the wheel. This is not to be confused with a locking hub, which is called a hub as well. This unit usually is supported by two bearings and is driven by the axle shaft.

  • Wheel Flange - The Wheel Flange is the flat mounting surface that the wheel is mounted to. This flange is either part of the wheel hub or made into the axle shaft depending on which type of axle is in question.

  • Yoke - The work Yoke refers to the Pinion Yoke. The pinion yoke links the pinion Shaft via a U-Joint to the drive shaft.

    • Now Hiring

      4 Wheel Parts is Hiring

      To see all of our current job openings

      Apply Now

    • Email Offers

      Sign up now to receive our latest promotions and exclusive offers.

    • Store Locator

      4 Wheel Parts Store Locator

      91 Stores in North America.
      Locate a store near you.

      Store Locator