G2 Axle & Gear Core 44 Rear Bare Housings

From $900.00

• American-made CORE 44 housings
• Feature forged bearing caps
• G-lock adjuster nut system to set backlash and carrier bearing preload
• Additional ribbing on the cast center section
• California Residents: WARNING

Dana Spicer Dana 44 Front Axle Assemblies

From $1,051.99

• Genuine Spicers gears
• Thick axle tubes for improved strength
• Redesigned and thicker brackets
• Spicer chromoly axle shafts
• Performance differential cover and Spicer performance gasket
• Increased gross axle weight rating
• California Residents: WARNING

Dana Spicer Ultimate Dana 60 Axle Assemblies

From $8,499.99

• The strongest, most robust axle assembly on the market
• Massive Spicer SPL 70 u-joints—exclusive to Dana
• Provides optimal performance for lifted vehicles with larger tires
• Improved “rock solid” seals for optimal protection from environmental contamination
• Manufactured from cold-forged steel
• Spicer 35 spline SAE-4340 nickel chromoly steel axle shafts
• Warn 35 spline hub locks
• Allowing for wheel bearings to be serviced individually
• Easier to repair and service than unit bearing design
• High-strength, heavy gauge brackets
• Cover face rotated back for greater ground clearance
• Reinforced ribbing on bottom of carrier to prevent hang-ups on rocks or rough terrain
• Selectable electronic locking differentials
• Precision-forged gears offer ideal meshing, strength and durability
• Upper and lower control arms in same location as OE
• Better fit, less adjustment on control arm
• Genuine Made in the USA Spicer® 10" (256 mm) ring and pinion gear
• Precision heat treated for optimal hardness and durability
• Face hobbed for precise mating of gear teeth and a quieter ride
• Lapped to reduce noise and heat
• Spicer 1350 Strap-style/Half-round end yoke
• Axle tubes: 3.5" tube diameter/.370" wall thickness
• Helps prevent steering from being knocked out of alignment
• California Residents: WARNING

TeraFlex CRD60 HD Axle Assemblies

From $2,620.99

• Tera CRD60 specific high-pinion rear axle housing design
• HD bearing caps increase rigidity and reduce ring and pinion distortion
• Constant Radius Design (CRD) provides maximum ground clearance regardless of pinion angle
• Built-in “skimmer” cuts ring gear oil halo and forces it into the pinion bearings
• Outer pinion bearing pocket features a renewable oil reservoir that sends cool oil to the pinion bearing
• Oversized outer pinion bearing handles increased torque and high-load conditions
• High-capacity housing holds maximum amount of oil
• Asymmetric housing design for extra-long tube side strength
• Pre-installed inner axle seals
• Ductile cast iron housing with increased rib gussets
• HD ductile iron differential cover with increased cover mounting area
• Integrated lower control arm skid plates
• High-flow oil passages
• Bottom oil drain hole for simple fluid changes
• Reinforced rear track bar mount with multiple mounting locations
• UV protected triple-stage powder coat for corrosion resistance
• 1/4”-thick CNC laser cut axle brackets for extreme strength
• Pre-installed upper control arm bushings
• Proper pinion angle for lifted applications
• Features a raised pinion angle and raised track bar bracket
• Pre-tapped hole on spring perch for bump stop extensions
• Pre-drilled holes for limit straps and lower spring retainers
• Retains all ESP, ABS, and speedometer sensor capability
• 100% engineered, designed, and built in the USA with new components

TeraFlex Dana 60 Axle Assemblies

From $3,582.99

• Maximum Ground Clearance
• Adjustable Control Arm And Track Bar Mounting Locations
• Comes complete with properly matched components
• Ultra-reliable package that exceeds stock axle performance, durability and reliability
• California Residents: WARNING

Currie Enterprises Currie 44 Front Crate Axle Assemblies

From $5,600.00

• Currie 44 high-pinion nodular iron center section with thicker walls and webbing to deliver superior strength and rigidity
• Large 3-inch diameter .375 wall axle tubes (left) are more than twice as strong as the stock 2.5-inch diameter .250 wall tubes
• Currie heavy duty forged inner knuckles (right) are significantly stronger that the stock knuckles (left) and are designed for serious off-road use with up to 37” tall tires
• Currie Performance 4340 Chromoly axles provide superior strength over OEM carbon steel axles
• Upper control arm mounts feature rebuildable Johnny Joints® for improved suspension articulation
• Lower control arm mounts are one piece construction with integrated skid plates to help fend off bracket seeking rocks
• 1350 pinion yoke provides increased strength over the stock companion flange
• Currie nodular-iron differential cover to defend against those unfortunate rock encounters
• California Residents: WARNING

Currie Enterprises Currie 60 Rear Crate Axle Assemblies

From $5,300.00

• Currie 60 high-pinion, radius bottom center section greatly improves obstacle slide-over by presenting a smooth curve rather than the sharp edge found on other 60 housings
• Highest measured ground clearance of any 60 on the market (and that’s including the integrated skid plate), guess the other guys can’t read a tape measure
• Integrated AR400 hardened steel skid plate resists deformation and gouging to slide over obstacles far better than iron housings or mild steel plates
• Large diameter pinion bearings to handle the increased load of reverse geometry gears
• High volume flow-thru recirculating oil system keeps pinion bearings bathed in cool oil, reducing operating temperatures and eliminating oil starvation issues
• Large 3-inch diameter .375 thick axle tubes deliver superior strength without sacrificing ground clearance or being overweight
• Currie Performance 40-spline 4340 chrome moly semi-floating axles, the largest and strongest standard axle in the industry
• Massive Set 80 axle bearings allow for larger axle diameter through the bearing for increased strength
• California Residents: WARNING

Currie Enterprises Currie 60 Front Crate Axle Assemblies

From $7,500.00

• Currie 60 high-pinion radius bottom center section greatly improves obstacle slide-over by presenting a smooth curve rather than the sharp edge found on other 60 housings
• Integrated AR400 hardened steel skid plate resists deformation and gouging to slide over obstacles far better than iron housings or mild steel plates
• Large diameter outer pinion bearing (right) is designed for the demands of reverse rotation/high pinion housings. Stock low pinion bearing (left)
• High volume flow-thru recirculating oil system keeps pinion bearings bathed in cool oil, reducing operating temperatures and eliminate oil starvation issues
• Large 3” diameter .375” thick wall axle tubes (left) are more than twice as strong as the stock Dana® 44 (right)
• Upper control arm mounts feature rebuildable Johnny Joints® for improved suspension articulation
• Big 13.250 inch diameter vented rotors (+1.3 inches larger than stock) provide the increased brake torque required for stopping large tires
• Lower control arm mounts are one piece construction with integrated skid plates to help fend off bracket seeking rocks
• California Residents: WARNING

Currie Enterprises Currie Extreme 60 Front Crate Axle Assemblies

From $9,850.00

• Currie Extreme 60 stage-2 high-pinion nodular iron center section is simply the strongest 60 series casting we offer, with 9 lbs. more reinforcement in critical areas over the already strong Stage-1 center section
• Radius bottom center section greatly improves obstacle slide-over by presenting a smooth curve rather than the sharp edge found on other 60 housings
• Integrated AR400 hardened steel skid plate resists deformation and gouging to slide over obstacles far better than iron housings or mild steel plates
• Ring gear load bolt eliminates deflection, to dramatically increase the torque handling capacity
• Highest measured ground clearance of any 60 on the market (and that’s including the integrated skid plate), guess the other guys have trouble reading a tape measure
• Currie Performance 35-spline 4340 chrome moly inner and outer axles for superior end to end strength
• High volume flow-thru recirculating oil system keeps pinion bearings bathed in cool oil, reducing operating temperatures and extending bearing life
• Currie nodular iron differential cover with integrated upper control arm mount features rebuildable Johnny Joints® for superior articulation and service life
• Currie Currectlync® 1 5/8” diameter heat treated Chromoly tie rod for unsurpassed strength and reliability
• Big 13.250 rotors (+1.3 inch over stock) and large dual piston calipers provide the stopping power required for 37 inch and larger tires
• California Residents: WARNING

TeraFlex Tera44 HD Axle Assemblies

From $1,570.97

• 3.25” O.D. x 0.25” wall axle tube increases torsional strength to resist bending with minimal weight increase
• Asymmetric housing design for extra-long tube side strength
• Pre-installed inner axle seals
• HD forged inner knuckles with greater upper and lower section strength
• Ductile cast iron housing with increased rib gussets
• HD ductile iron differential cover
• Smooth radius bottom design to glide over rocks and obstacles
• Integrated lower control arm skid plates
• High-flow oil passages and bottom oil drain hole for simple fluid changes
• Reinforced front track bar mount (ties into spring pad) for greater strength
• UV protected triple-stage powder coat for corrosion resistance
• 1/4”-thick CNC laser cut axle brackets for extreme strength
• Integrated factory location upper control arm mount
• Pre-installed upper control arm bushings
• Proper pinion angle for lifted applications
• Pre-tapped hole on spring perch for bump stop extensions
• Pre-drilled holes for limit straps and lower spring retainers
• Retains all ESP, ABS, and speedometer sensor capability
• 100% engineered, designed, and built in the USA with new components

TeraFlex Tera60 HD Axle Assemblies

From $10,943.99

• 3.25” O.D. x 0.375” wall DOM axle tube for superior strength vs. weight
• Fixed spindle mount hub assembly
• Tera60 specific high-pinion front axle housing design
• Outer pinion bearing pocket features a renewable oil reservoir that sends cool oil to the pinion bearing
• Oversized outer pinion bearing handles increased torque and high-load conditions
• High-capacity housing holds maximum amount of oil
• Asymmetric housing design for extra-long tube side strength
• Pre-installed inner axle seals
• HD forged inner knuckles with greater upper and lower section strength
• Ductile cast iron housing with increased rib gussets
• HD ductile iron differential cover
• Smooth radius bottom design to glide over rocks and obstacles
• Integrated lower control arm skid plates
• High-flow oil passages
• ottom oil drain hole for simple fluid changes
• Reinforced front track bar mount (ties into spring pad) for greater strength
• UV protected triple-stage powder coat for corrosion resistance
• 1/4”-thick CNC laser cut axle brackets for extreme strength
• Integrating the front upper control arm mounts into the housing increases up travel an additional 2” compared to other aftermarket Dana 60 axles
• Pre-installed upper control arm bushings
• Proper pinion angle for lifted applications
• Features a raised pinion angle and raised track bar bracket
• Pre-tapped hole on spring perch for bump stop extensions
• Pre-drilled holes for limit straps and lower spring retainers
• Retains all ESP, ABS, and speedometer sensor capability
• 100% engineered, designed, and built in the USA with new components

TeraFlex Tera30 HD Axle Assemblies

From $2,620.99

• 3.25” O.D. x 0.25” wall axle tube increases torsional strength to resist bending with minimal weight increase
• Asymmetric housing design for extra-long tube side strength
• Pre-installed inner axle seals
• HD forged inner knuckles with greater upper and lower section strength
• Ductile cast iron housing with increased rib gussets
• HD ductile iron differential cover
• Smooth radius bottom design to glide over rocks and obstacles
• Integrated lower control arm skid plates
• High-flow oil passages and bottom oil drain hole for simple fluid changes
• Reinforced front track bar mount (ties into spring pad) for greater strength
• UV protected triple-stage powder coat for corrosion resistance
• 1/4”-thick CNC laser cut axle brackets for extreme strength
• Integrated factory location upper control arm mount
• Pre-installed upper control arm bushings
• Proper pinion angle for lifted applications
• Pre-tapped hole on spring perch for bump stop extensions
• Pre-drilled holes for limit straps and lower spring retainers
• Retains all ESP, ABS, and speedometer sensor capability
• 100% engineered, designed, and built in the USA with new components

Dynatrac ProRock 44 Front Axle Housings

From $3,728.00

• Patented ProRock shape delivers more ground clearance than a Dana 30
• In fact, that’s the most ground clearance of any Dana 44-based axle
• The strongest end forgings, made by Dynatrac in the USA
• Rock-proof nodular-iron Dynatrac differential cover included
• Heavy-duty 3.0-inch diameter axle tubes with .313-inch wall thickness
• DOM (drawn-over mandrel) tubing
• New upper suspension bushings already installed
• Laser cut suspension brackets that are thicker and stronger than factory
• Includes new replacement OE balljoints, already installed
• Retains the Next-Gen JK 44 ring and pinion for more strength over earlier Dana 44 designs
• Entire axle housing is manufactured in the USA

Dana Spicer Ultimate Dana 80 Axles

From $14,013.99

• Dana 80 axle model
• Chromoly axle shaft material
• Available with different traction devices
• Available for front and rear applications

Dana Spicer Ford 9inch Cases

From $492.99

Currie Enterprises Currie 70 Front Crate Axle Assemblies

From $15,352.95

Currie Enterprises Currie 70 Rear Crate Axle Assemblies

From $14,000.00

Dynatrac HardCore ProRock 60/60 Axle

From $19,397.30

• Dynatrac exclusive patented ProRock nodular-iron, high-pinion ProRock 60 centersection
• Best-in-class ground clearance and more ground clearance than a factory Dana 44
• Dual-Sump High Volume (DSHV) oiling system to ensure the outer pinion bearing is never without lubrication
• U.S.-made forged, double heat-treated 1480 35-spline, 1-ton axleshaft assemblies
• Dynatrac HD BallJoints
• Dynatrac HD tie rod, 4140 heat-treated steering arm
• California Residents: WARNING