TeraFlex CRD60 HD Axle Assemblies

From $2,620.99

• Tera CRD60 specific high-pinion rear axle housing design
• HD bearing caps increase rigidity and reduce ring and pinion distortion
• Constant Radius Design (CRD) provides maximum ground clearance regardless of pinion angle
• Built-in “skimmer” cuts ring gear oil halo and forces it into the pinion bearings
• Outer pinion bearing pocket features a renewable oil reservoir that sends cool oil to the pinion bearing
• Oversized outer pinion bearing handles increased torque and high-load conditions
• High-capacity housing holds maximum amount of oil
• Asymmetric housing design for extra-long tube side strength
• Pre-installed inner axle seals
• Ductile cast iron housing with increased rib gussets
• HD ductile iron differential cover with increased cover mounting area
• Integrated lower control arm skid plates
• High-flow oil passages
• Bottom oil drain hole for simple fluid changes
• Reinforced rear track bar mount with multiple mounting locations
• UV protected triple-stage powder coat for corrosion resistance
• 1/4”-thick CNC laser cut axle brackets for extreme strength
• Pre-installed upper control arm bushings
• Proper pinion angle for lifted applications
• Features a raised pinion angle and raised track bar bracket
• Pre-tapped hole on spring perch for bump stop extensions
• Pre-drilled holes for limit straps and lower spring retainers
• Retains all ESP, ABS, and speedometer sensor capability
• 100% engineered, designed, and built in the USA with new components

TeraFlex Rzeppa Factory Replacement CV Kit

From $184.99

• TeraFlex has created the High Angle Rzeppa Factory Replacement CV Joint Kit to help you retain your driveline
• With the High Angle CV housing, it can decrease the boot failure that's commonly seen in taller lifts
• Included in the kit are socket head bolts, the CV joint assembly, a 6 mm Allen wrench, the high angle CV housing boot and the cap, the bolt flanges, and low friction CV grease
• California Residents: WARNING

TeraFlex NP231 Extreme Short Shaft Kit

From $399.99

• Extreme Short Shaft Kit
• With 231 transfer case
• Eliminates slip yoke
• Requires a longer CV style drive shaft
• California Residents: WARNING

TeraFlex Differential Covers

From $115.99

• Designed to offer extreme protection from rocks, obstacles and other debris on the trail
• Covers are cast from the same high-strength ductile-iron as our their axle housings
• Features a large diameter fill tube/inspection port at the top to accommodate a funnel or gear oil bottle pour spout
• Fluid level port doubles as a mid-height inspection port
• California Residents: WARNING

TeraFlex Ball Joints

From $155.99

• 1045 carbon steel housing with magnesium phosphate coated assembly
• 4140 chromoly ball/stud with magnesium phosphate anti-corrosion coating
• Factory style serrated flanged castle nut
• CR black neoprene boot
• California Residents: WARNING

Motive Gear Ring and Pinion Sets

From $1,499.99

• Ring and Pinion Sets
• Stock performance ring and pinions
• Easy setup, superior strength, quality, and a vast ratio selection
• Backed by rigid quality control processes
• 2 year / 100,000 mile no-nonsense warranty
• California Residents: WARNING

TeraFlex Short Shaft SYE

From $11.99

• Eliminates slip yoke and need for transfer case drop
• Withstands 50% more torque
• Increases rear drive shaft length by 4 inch
• Requires use of CV style rear drive shaft
• California Residents: WARNING

TeraFlex Axle Tube Seals

From $209.99

• The outer triple O ring tube seal presses into the housing and provides a positive mud and water barrier
• The inner double axle seal surface is designed with a cavity between the seal surfaces to form a grease filled pocket providing lubrication for the seals and provides another barrier to mud and grime
• These are the same seals that were developed, proven and currently used in many NASCAR applications
• California Residents: WARNING

TeraFlex U-Bolt Yoke Conversion Kit

From $131.99

• Rear Axle
• Includes Yoke
• U-Bolts
• Hardware
• California Residents: WARNING

Motive Gear Full Spools

From $166.99

• If you are looking for maximum traction and strength nothing beets a full spool.
• Not Recommended For Street Use
• California Residents: WARNING

TeraFlex Tera44 Rubicon Locker Sensor and Actuator Plug Kit

From $32.99

• TeraFlex R44/Rubicon Dana 44 Locker Sensor and Actuator Plug Kit is for use in Front Teraflex R44 and Factory Rubicon Dana 44 axle housings that will be using an aftermarket locker
• Requires the factory electronic locker holes to be blocked
• The locker sensor plug included in this kit is machined to accept the ARB airline bulkhead for a clean and easy install with no drilling through your axle housing required
• It also conveniently accepts the rubber grommet used by the E-Locker, with the same perks as the ARB install
• This kit has you covered for whichever aftermarket locker you choose
• It includes the sensor plug, actuator plug, O-rings, and hardware
• California Residents: WARNING

Teraflex Full Float Conversion Kits

From $1,383.97

• Universal for axles with 35 splines
• Includes cap
• California Residents: WARNING

TeraFlex Dana 60 Axle Assemblies

From $3,582.99

• Maximum Ground Clearance
• Adjustable Control Arm And Track Bar Mounting Locations
• Comes complete with properly matched components
• Ultra-reliable package that exceeds stock axle performance, durability and reliability
• California Residents: WARNING

TeraFlex Tera44 HD Axle Assemblies

From $2,974.99

• 3.25” O.D. x 0.25” wall axle tube increases torsional strength to resist bending with minimal weight increase
• Asymmetric housing design for extra-long tube side strength
• Pre-installed inner axle seals
• HD forged inner knuckles with greater upper and lower section strength
• Ductile cast iron housing with increased rib gussets
• HD ductile iron differential cover
• Smooth radius bottom design to glide over rocks and obstacles
• Integrated lower control arm skid plates
• High-flow oil passages and bottom oil drain hole for simple fluid changes
• Reinforced front track bar mount (ties into spring pad) for greater strength
• UV protected triple-stage powder coat for corrosion resistance
• 1/4”-thick CNC laser cut axle brackets for extreme strength
• Integrated factory location upper control arm mount
• Pre-installed upper control arm bushings
• Proper pinion angle for lifted applications
• Pre-tapped hole on spring perch for bump stop extensions
• Pre-drilled holes for limit straps and lower spring retainers
• Retains all ESP, ABS, and speedometer sensor capability
• 100% engineered, designed, and built in the USA with new components

TeraFlex Tera60 HD Axle Assemblies

From $10,943.99

• 3.25” O.D. x 0.375” wall DOM axle tube for superior strength vs. weight
• Fixed spindle mount hub assembly
• Tera60 specific high-pinion front axle housing design
• Outer pinion bearing pocket features a renewable oil reservoir that sends cool oil to the pinion bearing
• Oversized outer pinion bearing handles increased torque and high-load conditions
• High-capacity housing holds maximum amount of oil
• Asymmetric housing design for extra-long tube side strength
• Pre-installed inner axle seals
• HD forged inner knuckles with greater upper and lower section strength
• Ductile cast iron housing with increased rib gussets
• HD ductile iron differential cover
• Smooth radius bottom design to glide over rocks and obstacles
• Integrated lower control arm skid plates
• High-flow oil passages
• ottom oil drain hole for simple fluid changes
• Reinforced front track bar mount (ties into spring pad) for greater strength
• UV protected triple-stage powder coat for corrosion resistance
• 1/4”-thick CNC laser cut axle brackets for extreme strength
• Integrating the front upper control arm mounts into the housing increases up travel an additional 2” compared to other aftermarket Dana 60 axles
• Pre-installed upper control arm bushings
• Proper pinion angle for lifted applications
• Features a raised pinion angle and raised track bar bracket
• Pre-tapped hole on spring perch for bump stop extensions
• Pre-drilled holes for limit straps and lower spring retainers
• Retains all ESP, ABS, and speedometer sensor capability
• 100% engineered, designed, and built in the USA with new components

Motive Gear AMC Model 20 Carrier Shim Kit

From $8.99

• Carrier Shim Kit
• For setting ring and pinion pattern and set back lash
• Factory style replacement part
• California Residents: WARNING

Motive Gear Mini Spools

From $100.99

• If you are looking for maximum traction and strength nothing beets a full spool.
• Not Recommended For Street Use
• California Residents: WARNING

TeraFlex Tera30 HD Axle Assemblies

From $2,620.99

• 3.25” O.D. x 0.25” wall axle tube increases torsional strength to resist bending with minimal weight increase
• Asymmetric housing design for extra-long tube side strength
• Pre-installed inner axle seals
• HD forged inner knuckles with greater upper and lower section strength
• Ductile cast iron housing with increased rib gussets
• HD ductile iron differential cover
• Smooth radius bottom design to glide over rocks and obstacles
• Integrated lower control arm skid plates
• High-flow oil passages and bottom oil drain hole for simple fluid changes
• Reinforced front track bar mount (ties into spring pad) for greater strength
• UV protected triple-stage powder coat for corrosion resistance
• 1/4”-thick CNC laser cut axle brackets for extreme strength
• Integrated factory location upper control arm mount
• Pre-installed upper control arm bushings
• Proper pinion angle for lifted applications
• Pre-tapped hole on spring perch for bump stop extensions
• Pre-drilled holes for limit straps and lower spring retainers
• Retains all ESP, ABS, and speedometer sensor capability
• 100% engineered, designed, and built in the USA with new components

Motive Gear Ring and Pinion Installation Kits

From $162.99